User manual ABIT SG-95
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual ABIT SG-95. We hope that this ABIT SG-95 user guide will be useful to you.
Manual abstract: user guide ABIT SG-95
Detailed instructions for use are in the User's Guide.
[. . . ] Introduction Hardware Setup BIOS Setup Driver & Utility CD
SG-95
Motherboard Socket 775
Intel Pentium D / Pentium 4 / Celeron / Celeron D / Core 2 Duo
LGA775 mATX Motherboard SiS 662/SiS 966L 800MHz FSB DDR2 667/533 Integrated SiS Mirage 1 Graphics GPU 2x SATA 1. 5Gb/s RAID 0/1
Appendix
User's Manual
7. 1 HD Audio
SG-95 User's Manual English, 1st Edition August, 2006
Copyright and Warranty Notice The information in this document is subject to change without notice and does not represent a commitment on part of the vendor, who assumes no liability or responsibility for any errors that may appear in this manual. No warranty or representation, either expressed or implied, is made with respect to the quality, accuracy or fitness for any particular part of this document. In no event shall the manufacturer be liable for direct, indirect, special, incidental or consequential damages arising from any defect or error in this manual or product. Product names appearing in this manual are for identification purpose only and trademarks and product names or brand names appearing in this document are the property of their respective owners. [. . . ] Connect the single end (blue connector) at the longer length of ribbon cable to the IDE port of this board, the other two ends (gray and black connector) at the shorter length of the ribbon cable to the connectors of your hard drives.
Make sure to configure the "Master" and "Slave" relation before connecting two drives by one single ribbon cable. The red line on the ribbon cable must be aligned with pin-1 on both the IDE port and the hard-drive connector.
2-12
SG-95
2. 6. 2 Serial ATA Connectors
Each SATA connector serves as one single channel to connect one SATA device by a thin SATA cable.
Hardware Setup
To connect SATA device: 1. Attach either end of the signal cable to the SATA connector on motherboard. Attach the SATA power cable to the SATA device and connect the other end from the power supply.
The motherboard in this illustration is served for DEMO only, may not be the same type or model as the one described in this user's manual.
SG-95
2-13
2. 6. 3 Additional USB 2. 0 Port Headers
Each header supports 2x additional USB 2. 0 ports by connecting bracket or cable to the rear I/O panel or the front-mounted USB ports of your chassis.
Pin 1 3 5 7
Pin Assignment VCC Data0 Data0 + Ground
Pin 2 4 6 8 10
Pin Assignment VCC Data1 Data1 + Ground NC
Make sure the connecting cable bears the same pin assignment.
2-14
SG-95
2. 6. 4 Internal Audio Connectors
This connector connects to the audio output of internal CD-ROM drive or add-on card.
Hardware Setup
2. 6. 5 Front Panel Audio Connection Header
This header provides the front panel connection for HD (High Definition) Audio, yet for AC'97 Audio CODEC connection, you must carefully check the pin assignment before connecting from the front panel module. An incorrect connection may cause malfunction or even damage the motherboard. Please do not connect the "Ground" cable or "USB VCC" cable from the front panel module to the Pin 4 "AVCC" of this header.
Pin 1 2 3 4 5 6 7 9 10
Pin Assignment (HD AUDIO) MIC2 L AGND MIC2 R AVCC FRO-R MIC2_JD F_IO_SEN FRO-L LINE2_JD
Pin 1 2 3 4 5 6 7 9 10
Pin Assignment (AC'97 AUDIO) MIC In GND MIC Power NC Line Out (R) NC NC Line Out (L) NC
SG-95
2-15
Driver Configuration for AC'97 audio connection: The audio driver is originally configured to support HD Audio. Click "Audio I/O" tab, and then click "Connector Settings".
3. Click "Disabled front panel jack detection", and then click "OK" to confirm.
2-16
SG-95
2. 6. 6 PCI and PCI Express X16, X1 Slots
Install PCI Express X16 graphics card into slot "PCIEXP1". Install PCI cards into slots "PCI1" and/or "PCI2".
Hardware Setup
SG-95
2-17
2. 7 Connecting I/O Devices
· · · · · · · ·
Mouse: Connects to PS/2 mouse. LPT1: Connects to printer or other devices that support this communication protocol. COM1: Connects to external modem, mouse or other devices that support this communication protocol. USB1/USB2: Connects to USB devices such as scanner, digital speakers, monitor, mouse, keyboard, hub, digital camera, joystick etc. (Surround Left / Surround Right): Connects to the surround left and surround right channel in the 7. 1 channel audio system. (Center / Subwoofer): Connects to the center and subwoofer channel in the 7. 1 channel audio system. (Rear Left / Rear Right): Connects to the rear left and rear right channel in the 7. 1 channel audio system. Line-Out: Connects to the front left and front right channel in the 7. 1-channel or regular 2-channel audio system. Mic-In: Connects to the plug from external microphone.
2-18
SG-95
3. BIOS Setup
This motherboard provides a programmable EEPROM so that you can update the BIOS utility. The BIOS (Basic Input/Output System) is a program that deals with the basic level of communication between processor and peripherals. Use the BIOS Setup program only when installing motherboard, reconfiguring system, or prompted to "Run Setup". After powering up the system, the BIOS message appears on the screen, the memory count begins, and then the following message appears on the screen:
PRESS DEL TO ENTER SETUP
If this message disappears before you respond, restart the system by pressing <Ctrl> + <Alt> + <Del> keys, or by pressing the Reset button on computer chassis. Only when these two methods fair should you restart the system by powering it off and then back on. [. . . ] (Illustrate the over-clocking status if you had done so. ) Example: Intel 650 3. 4GHz (OC FSB=220MHz) Memory brand: Type in the brand and model name of your memory module. Example: Memory brand: Kingston (KVR533D2N4/1G) Memory size: Type in the size of your memory module. Example: 512M* 4PCS Memory configuration: Type in the memory configuration in BIOS setting. Example: Memory Timing: 2. 5-3-3-7 @533MHz Graphics information: Note Graphics card's brand, model and driver version Graphics card: Type in the brand and model name of your graphics card. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE ABIT SG-95
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual ABIT SG-95 will begin.