User manual AMERICAN AUDIO Q-2422SX

[. . . ] With your channel faders in the maximum position, use the channel trim level to set an average output level of about +4dB on you master level meter. Headphones - To avoid sever hearing damage alway be sure the headphone level is set to minimum before plugging them in. Never put the headphone on without making sure the headphone level is turned down. Main Mic - The main mic connector uses a Nuetrik combo plug which allows you to connect either a 1/4" unbalanced jack or by a standart 3-pin XLR balanced connector. [. . . ] You can only control this signal after you have switched the PHONO / AUX SELECTOR SWITCH (36) on the rear panel to AUX, plus you must change the PHONO/AUX/LINE SWITCH (5) on the front panel to PHONO/AUX. The signal is then controlled via the CH-1 AND CH-2 FADERS (6). ©American DJ Audio® - www. americandj. com - Q-2422/SXTM User Instructions page 5 Front Panel 15 5 4 3 2 21 20 24 16 1 22 19 10 18 6 17 8 7 9 13 11 12 14 23 (1) POWER SWITCH - Red LED will light when power is ON. (2) MASTER LEVEL - Dual LED's show the level of the left and right master output. (3) CHANNEL GAIN CONTROL - Used to set the level of the output signal for its designated channel. (4) CHANNEL BASS/MID/TREBLE CONTROL - Used to increase or decrease the LOW's, MID's, and HI's of the output signal. The Q-2422/SX features "Rotary Kills" with -35dB to +15dB output control. (5) PHONO/AUX/LINE SWITCH - Used to select the input to be sent to the individual channel. The selectors for AUX1/PHONO1 and AUX2/PHONO2 are on the rear panel (36). (7) CUE BUTTONS - Engage the CUE button to monitor the assigned channel. (8) FEATHER FADERTM CROSSFADER - Mixes the signals of the assigned channels. To assign channels use the ASSIGN SWITCH (17) located on either side of the crossfader. When the crossfader is set in the center position, both assigned channels can be heard at once. (9) ON/OFF "Q" START- Start and stop the CD Player with the slide of the fader. The ON/OFF "Q" START switch activates this FADER "Q" START feature. When in the ON position, the FADER "Q" START allows the signal to return automatically to preset digital CUE POINTS on your American DJ CD Player (also featuring FADER "Q" START). For example, each time you slide the crossfader to far left, the CD Player will be triggered to play the song from the beginning of the preset CUE POINT. Refer to your American DJ CD Player User Manual for setting CUE POINTS. Turn the ON/OFF SWITCH to the OFF position to disengage the "Q" Start function and resume to a normal fader. (10) TALKOVER SWITCH - While in the ON position the microphone can be used at any time, while this will not attenuate any other channels. When the switch is in the TALKOVER position, the microphone is ©American DJ Audio® - www. americandj. com - Q-2422/SXTM User Instructions page 6 Front Panel Cont. hot, meaning that when the microphone is in use all channels attenuate -15dB except the MIC. When the microphone is not being spoken into all channels return to normal. In the OFF position, all signals return to their original level and the microphone is off. [. . . ] BASS & TREBLE for MIC 1 can be adjusted by the MIC BASS CONTROL KNOB (19) and the MIC TREBLE CONTROL KNOB (19). There is also a XLR-plug for MIC 1 (15) on the front panel. Replacing the Crossfader 1. Using a number two Phillips screw driver, unscrew the each of the stainless steel retain screws that hold the crossfader in place. After removing the crossfader, disconnect the ribbon cable that attaches the crossfader to the PC board. [. . . ]