User manual AOC ENVISION A42W64AT4

[. . . ] Do not defeat the safety purpose of the polarized or grounding-type plug. When the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. . Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. [. . . ] Up: Press to select the next higher Programme number or move up in Menu operation Power switch: Press to power on or power off the TV set . Check front panel LED for proper power connection: Blue color indicates this TV set is powered on; Red color indicates this TV set is in standby state. Push POWER KEY on Remote Control or Power key on Front panel controls to switch the TV from stand by state to ON state. This TV will power on and you can see display on screen within a few minutes. Once you see information displayed on screen, press Digital button on Remote Control or MODE key on front panel continuously to select TV as input source. Use Auto channel search in "Setup Menu" to search all channels in your location. After Auto channel search is completed, press "CHup" or "CHdown" key on remote control to select the next lower or higher channel. Refer to the following pages for operating procedures: Remote Control ­ page 9. TV Channel Arrangement ­ page 13. POWER KEY Ch14. 0 12:00AM TV channel information 6 Connection to other equipment Please connect this TV Set to other equipment as picture below. You may have many types of equipment as: DVD, VCD, VCR, Set Top Box, X-Box and so on. (View from back of the TV set, left to right) INPUT CONNECTION OF VIDEO SIGNAL(DVD/VCD/VCR) s-video Y R AV1-INPUT W B s-video Y R W 7 Connection to other equipment We have 2 component signal input jacks: Y Cb Cr and Y Pb Pr. If your DVD or Set Top Box have Y Cb Cr or Y Pb Pr output, you can connect it to Y Cb Cr or Y Pb Pr input jack. Some DVD or Set Top Box need to set to Y Cb Cr or Y Pb Pr output Notice: If you see that display abnormality in screen, you need to check the cable connection and DVD setup. G B R R W INPUT CONNECTION OF PC SIGNAL(PC/DVD) Notice: If you see that display abnormality in screen, you need to check the cable connection and DVD setup. Notice: The PC output can not set out of range. The highest resolution input is 1280 X 1024 / 60Hz. Some PC models cannot be connected to the set. 24PIN DVI R/L INPUT 15PIN DVI R/L INPUT D-SUB 15 Pin: Connect D-SUB signal cable VGA cable from PC to D-SUB jack at the back of this display. And connect the earphone cable from PC earphone output jack to AUDIO input jack near to the D-SUB jack. Setup: Use the key "Digital" Remote Control Transmitter or "MODE" on Front panel controls in key to select source to "VGA"state. DVI-D: Connect DVI-D 24 Pin signal cable TMDS cable from equipment with DVI-D jack to the back of this display. And connect earphone cable from equipment with earphone output jack to AUDIO input jack near the DVI-D jack. Menu Language: Select language for menu (English Español Français Portuguese) . DTV signal menu indicates signal strength in real-time. Auto channel scan menu displays channel number being scanned. Manual Channel Set Menu Displays all the channel numbers that are found. Add or delete Channel number. Channel Labels Menu allows user labeling. 10 OSD Menu Descriptions Video Menu . Press " " or " " to move the cursor up or down the sub-item list. [. . . ] ·Go to the Setup Menu (Menu-->Setup) and install the channels again, searching Air/Cable as appropriate. Check the DTV signal via Menu --> Setup --> DTV Signal Adjust the direction of your antenna to improve the signal Re-install the channels if needed. ·Check antenna connection, aerial location, and direction Re-scan Channels. Some channels are missing / are not found. No Picture, No Sound Interference, Noisy Distorted picture, Noisy ·Check whether colour setting is at minimum. Normal Colour, No Sound 15 Troubleshooting The plasma TV panel is manufactured using an extremely high level of precision technology, however, sometimes some parts of the screen may be missing picture elements or have luminous spots. [. . . ]