User manual ART TRANSIT SYSTEM

[. . . ] Built in power supply and single high 19-inch rack mount format allows for easy installation and reliable long-term operation. FEATURES: · · · · · · · · Eight Independent Input Channels Level and Tone Controls on each Channel Balanced XLR Microphone and 1/4-inch Unbalanced Line Inputs on each Channel Full +48 Volt Phantom Power on XLR inputs with DIP Switch for each Channel Balanced TRS 1/4-inch Main Output Jack with Master Level Control RCA-type Pre-Fade Output Jack (Not Affected by the Master Level Control) RCA-type Aux Buss Input Jack for Channel Expansion Solid Single High Rack Mount Chassis w/ Built In Power Supply SPECIFICATIONS: · · · · · · · · · · · · · · · · · Input Connections: Output Connections: Input Impedance: Output Impedance: Maximum Input Level: Maximum Output Level: Phantom Power: Maximum Gain: Signal to Noise Ratio: THD: Equivalent Input Noise CMRR: Phase Shift: Power Requirements: Dimensions: (HxWxD in) Dimensions: (HxWxD mm) Weight: XLR-F balanced (8), 1/4-inch unbalanced (8), RCA (1) 1/4-inch balanced TRS (1), RCA (1) 2K Ohms Mic, 20K Ohms Line, 10K Ohms Aux. Bus In 200 Ohms balanced Main Out, 100 Ohms Pre-Fade Out -6dBu Mic, +18dBu Line +27dBu balanced, +21dBu unbalanced +48 Volts DC (regulated/low noise) 65dB/39dB mic/line >90dB typical <0. 01% typical -108dBu typical >52dB typical <10 degrees, 20Hz - 20kHz 120VAC / 50-60Hz, or 230VAC / 50 Hz, 15VA 1. 75 x 19 x 6 44. 5 x 483 x 152 6. 3 lbs. (2. 9kg) OPERATION a) Verify proper voltage selection on the IEC style power connector for your location. [. . . ] c) Connect shielded unbalanced line inputs to the ¼" inch jacks. d) For microphone channels requiring phantom power (for condenser microphones) set the appropriate PHANTOM POWER DIP switches in the down position. Do not engage phantom power on a channel unless it is for a condenser microphone. e) Switch on the power and set the MASTER LEVEL to the ½ way setting, then adjust the channel LEVEL controls as required for the best mix and level. Adjust the channel TONE controls for the desired balance of lows and highs. f) Re-adjust the MASTER LEVEL as required for best overall signal level. g) To patch two TRANSIT SYSTEM's for 16 channel input operation, run a shielded, unbalanced RCA type patch cable from the PREFADE OUT jack on mixer A to the AUX BUS INPUT jack on mixer B. ART reserves the right to make changes in design or make additions to or improvements upon this product without any obligation to install the same on products previously manufactured. ART shall not be liable for any consequential damages, including without limitation damages resulting from loss of use. Some states do not allow limitations of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific rights and you may have other rights, which vary from state to state. For units purchased outside the United States, an authorized distributor of Applied Research and Technology will provide service. SERVICE The following information is provided in the unlikely event that your unit requires service. Check to make sure the unit has power, all cables are connected correctly, and the cables themselves are in working condition. You may want to consult with your dealer for assistance in troubleshooting or testing your particular configuration. [. . . ] You may want to consult with your dealer for assistance in troubleshooting or testing your particular configuration. 2) If you believe the ART unit is at fault, go to www. artproaudio. com. You may contact Customer Service for more assistance, or directly request a Return Authorization for service in the "resources" area of the website. [. . . ]