User manual BOSCH 5060008728A
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual BOSCH 5060008728A. We hope that this BOSCH 5060008728A user guide will be useful to you.
Manual abstract: user guide BOSCH 5060008728A
Detailed instructions for use are in the User's Guide.
[. . . ] 15A Dedicated Branch Circuit.
Caution
For general residential kitchen ventilating use only. DO NOT use to exhaust hazardous or explosive materials or vapors.
Caution
Vent unit to the outside unless using recirculation kit. Note: If using recirculation kit, refer to instructions included with that unit.
Warning
To reduce the risk of fire, use only metal ductwork. Ducting: a) DAH93 and 94 models: 7" (8" is also acceptable, however a 7"-8" transition will also be required) b) DAH95 models with remote blower: 10" (7"10" transition is also needed. [. . . ] Consequently, Bosch recommends the hood be installed 30"-36" above the countertop. Make-Up Air: Local building codes may require the use of make-up air systems when using ducted ventilation systems greater than specified CFM of air movement. Consult your HVAC professional for specific requirements in your area.
Rear Filter Rail J Box
Figure 1 - DAH93 and DAH94 models
Blower Cord Connector Connector Access Panel
Figure 2 - DAH95 models with internal blower
Blower Cord Connector
Connector Access Panel
Blower
1. Unpack Hood
Pull hood from outer packaging and remove all packaging materials.
J Box
2. For horizontal discharge, remove the knockout in the back wall of the hood. For vertical discharge, remove the knockout in the top of the hood.
Mounting Plate
Rear Filter Rail
Figure 3 - DAH95 models with remote blower
Remote Wire Cover
3. Install Internal Blower (DAH95 models only)
If your hood is already equipped with a blower, or you will be using a remote blower, proceed to Step 4: Install Transition (next page). See Figure 2.
J Box Rear Filter Rail White Connector
3
Installation
4. Install Transition
For internal blower installation, install the 7" transition (included) to connect to 7" ducting. In this instance, an additional 7-8" transition must also be used (not included). Attach the transition with 4 #8 sheetmetal screws (included) and seal connection with duct tape. Mount the Hood
The DAH model hood can be mounted through the back wall or through the top. Once the preferred height is determined, locate the centerline (left to right) of the cooking appliance. From the centerpoint of the cooking appliance, measure up to the preferred height. Measure up an additional 9" to locate the centerline of the screw holes (see Figure 4). Install toggle bolts through drywall leaving 1/4" of the bolt exposed. Install one togglebolt 11 1/2" to the left of the centerline and one togglebolt 11 1/2" to the right of the centerline. See Figure 4 For the 36" hood, there are 2 additional installation points. These are also at the centerline height, but are 15 3/8" from the centerline in each direction. Place the hood by sliding the mounting holes in the hood over the bolts. [. . . ] Remove 2 hood electrical knockouts and install 1/2" conduit connectors. Run black, white and green supply wires through 1/2" conduit to hood electrical knockout behind J box. Connect power supply wires to hood wires behind J box (white to white, black to black, green to green). Run 5 wires (#14 AWG) in 1/2" conduit from the remote blower to the electrical knockout behind the remote wire cover. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE BOSCH 5060008728A
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual BOSCH 5060008728A will begin.