User manual DLS 226
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual DLS 226. We hope that this DLS 226 user guide will be useful to you.
Manual abstract: user guide DLS 226
Detailed instructions for use are in the User's Guide.
[. . . ] DLS 225, 226 and 257 have a separate cable filter wrapped in plastic cover. Inside the cover there is both a lowpass filter for the woofer and a highpass filter for the tweeter. The filters must be used, if you connect without them the sound becomes bad and you will destroy the tweeter.
INSTALLATION
Mount the speakers in the door or in the dashboard of your car. If you want an improved sound reinforce with a baffle of MDF-board or similar. [. . . ] The bass/mid speaker driver uses the new DLS EFR technology for improved sound quality. The filters must be used, if you connect without them the sound becomes bad and you will destroy the tweeter.
TWO/THREE-WAY SYSTEMS C4, C5A, C6A & C36
The 2-way systems have a separate tweeter. The filters are separate lowpass and highpass in small plastic boxes with selectable tweeter level in three steps inside. C36 is a 3-way system with a filter box where you can connect a woofer, a midrange speaker and a tweeter. The tweeter level can be adjusted in three steps inside the filter box. The C5 and C6 bass/mid speaker driver uses the new DLS EFR technology for improved sound quality. The filters must be used, if you connect without them the sound becomes bad and you will destroy the tweeter.
SPEAKER ENCLOSURES
If you want to install the speaker in an enclosure the normal size for a sealed type is: 4" (10 cm) speakers : 2-4 liters 5, 25" (13 cm) speakers : 6-8 liters 6, 5" (16, 5 cm) speakers : 10-12 liters 8" (20 cm) speakers : 15-20 liters 6 x 9" speakers : 15-20 liters 7 x 10" speakers : 20-25 liters These volumes are only a guideline, they can vary between different speakers. Contact your local DLS dealer for more exact information about your specific speaker.
SPEAKER FACTS FOR DLS CLASSIC SERIES
Model Woofer Mid Tweeter Nom. power 50 W 50 W 60 W 50 W 50 W 50 W 80 W 50 W 50 W 60 W 60 W 80 W 60 W 80 W 80 W 100 W 50 W 50 W 50 W 50 W 60 W 60 W Max power 80 W 80 W 120 W 80 W 80 W 80 W 120 W 80 W 80 W 90 W 90 W 120 w 90 W 120 W 120 W 150 W 80 W 80 W 80 W 80 W 90 W 90 W Sensitivity 92 dB 92 dB 92 dB 93 dB 92 dB 92 dB 92 dB 92 dB 94 dB 93 dB 94 dB 94 dB 93 dB 93 dB 93 dB 92 dB 91 dB 91 dB 92 dB 93 dB 93 dB 93 dB Magnet size 70 mm / 2, 75" 80 mm / 3, 15" 80 mm / 3, 15" 70 mm / 2, 75" 80 mm / 3, 15" 80 mm / 3, 15" 100 mm / 3, 94" 80 mm / 3, 15" 80 mm / 3, 15" 90 mm / 3, 54" 100 mm / 4" 105 mm / 4, 1" 100 mm / 4" 100 mm / 4" 100 mm / 4" 110 mm/4, 3" 80 mm / 3, 15" 80 mm / 3, 15" 70 mm / 2, 75" 80 mm / 3, 15" 80 mm / 3, 15" 80 / 70 mm Inst. depth 50 mm / 1, 97" 28 mm / 2, 28" 75 mm / 3" 50 mm /1, 97" 54 mm / 2, 12" 52 mm / 2" 80 mm / 3, 15" 60 mm / 2, 36" 58 mm / 2, 28" 61 mm / 2, 4" 62 mm / 2, 44" 87 mm / 3, 43" 58 mm / 2, 28" 83 mm / 3, 27" 83 mm / 3, 27" 87 mm/ 3, 42" 63 mm / 2, 48" 63 mm / 2, 48" 58 mm / 2, 28" 60 mm / 2, 36" 63 mm / 2, 48" 63 / 58 mm Mounting hole 120 mm / 4, 72" 145 mm / 5, 7" 150x220 mm / 5, 9x8, 7" 102 mm / 4" 120 mm / 4, 72" 145 mm / 5, 7" 150x220 mm / 5, 9x8, 7" 130 x 185 mm / 5, 1x7, 3" 102 mm / 4" 117 mm / 4, 6" 145 mm / 5, 7" 185 mm / 7, 282 130 x 185 mm / 5, 1x7, 3" 150x220 mm / 5, 9x8, 7" 150x220 mm / 5, 9x8, 7" 156x225 mm/6, 15x8, 86" 117 mm / 4, 6" 146 mm / 5, 75" 102 mm / 4" 120 mm / 4, 72" 156 mm / 5, 75" 146 / 102 mm Crossover 125 126 1269 224 225 226 269 257 424 425 426 428 457 960 962 1072 B5A* B6A* C4 C5A* C6A* C36 13 cm / 5, 25" 16, 5 cm / 6, 5" 6 x 9" 10 cm / 4" 13 cm / 5, 25" 16, 5 cm / 6, 5" 6 x 9" 5 x 7" 10 cm / 4" 13 cm / 5, 25" 16, 5 cm / 6, 5" 20 cm / 8" 5 x 7" 6 x 9" 6 x 9" 7" x 10" 13 cm / 5, 25" 16, 5 cm / 6, 5" 10 cm / 4" 13 cm / 5, 25" 16, 5 cm / 6, 5" 16, 5 cm / 6, 5" 16 mm / 0, 63" 16 mm / 0, 63" 50 mm / 2" 16 mm / 0, 63" 16 mm / 0, 63" 16 mm / 0, 63" 50 mm 16 mm / 0, 63" 16 mm / 0, 63" 20 mm / 0, 8" 20 mm / 0, 8" 20 mm / 0, 8" 25 mm / 1" 20 mm / 0, 8" 50 mm 20 mm / 0, 8" 25 mm / 0, 8" 50 mm piezo 16 mm / 0, 63" 16 mm / 0, 63" 20 mm / 0, 8" 20 mm / 0, 8" 20 mm / 0, 8" 4" 20 mm / 0, 8" Integrated Integrated Integrated Integrated Integrated Integrated Integrated Integrated Separate box Separate box Separate box Separate box Separate box Integrated Separate box Integrated Separate LP/HP Separate LP/HP Cable filter Separate boxes Separate boxes Separate boxes
* Speakers using the DLS EFR technology for improved sound quality.
RUNNING-IN PERIOD
Allow the speakers to play for at least 15-20 hours. SPEAKER PHASING
To be sure to have the correct speaker polarity (phase) you can check this by using a 1, 5 Volt battery. Connect a cable from the battery plus-pole to the speaker plus, and a cable from the battery minus to the speaker minus. If the speakers are correctly connected the speaker cone should move outwards on both right and left channel. This check must be made on the cables going from the speakers, to the output terminals of your car stereo or amplifier.
CONNECTION OF SPEAKERS
For speakers with integrated filters you just connect like this. Make sure the polarity is correct for both left and right side.
+ + -
Car stereo or amplifier
FILTER/CROSSOVER INSTALLATIONS
Filter installation and connection of coaxial speakers 424, 425, 426 and 457
Speaker connection and tweeter level select:
Use the red, blue and black cables to connect between the filter box and speaker terminal. Select tweeter level by moving the jumper inside the filter box between high / low. Make your own tests for best result.
INPUT WOOFER TW + -+-+-
Filter installation and connection of coaxial speakers 962 and 428
Red + Black Blue +
Red + Black Blue +
Tweeter level Green to red=high Green to yellow=low
2-way crossover
2-way crossover
On the cable filter box without screw terminals the level select is made on the outside by connecting the green cable to either the red or yellow one coming out from the box. Low level: Connect green and yellow wire.
Yellow
coaxial
Car stereo or amplifier
Car stereo or amplifier
coaxial
Red Green
FILTER/CROSSOVER INSTALLATIONS
Filter installation B5A and B6A
Tweeter
Filter installation C5 and C6
Tweeter
Red + Black Blue +
Black Yellow Red Tweeter level select: For High level connect yellow and red wire. Disconnect for Low level
Transp Black - Red + Black -
Red + Red +
Yellow Red Blue
High pass
Low pass
High pass
+
Black -
Blue + Black Red +
Low pass
Cable filter Low pass (blue)
Cable filter High pass (red)
Cable filter Low pass (green) Black -
Cable filter High pass (yellow) Red + Black -
Tweeter level select:
High level: Connect yellow and red wire. Low level: All circuits open.
Red +
Car stereo or amplifier
Car stereo or amplifier
Filter installation C4
Tweeter
Filter installation C4, C5A and C6A with separate boxes. [. . . ] Angled mounting: Put the cable through the hole in the rear end of the angled cup. Attach the cup to the surface with the double adhesive tape.
3
C
4
A
B
RECESSED MOUNTING:
You need a hole with a diameter of 43 mm/ 1, 7". Put the two metal wings through the two tracks in the center of the cup, just as the picture shows, and attach them with the M4 screw and nut through the center hole. The cup is attached to the door side when the metal wings is pressed to the back side of the door. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE DLS 226
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual DLS 226 will begin.