User manual DOMETIC MSP 1012

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual DOMETIC MSP 1012. We hope that this DOMETIC MSP 1012 user guide will be useful to you.


DOMETIC MSP 1012 : Download the complete user guide (4925 Ko)

Manual abstract: user guide DOMETIC MSP 1012

Detailed instructions for use are in the User's Guide.

[. . . ] Maintenance and repair work may only be carried out by qualified personnel who are familiar with the risks involved and the relevant regulations. The device must be set up and fastened in such a way that it cannot tip over or fall down. Take the precautions necessary to ensure that children cannot interfere with operation. Dangerous situations may occur which cannot be recognised by children! [. . . ] Display Orange, constantly lit Orange, slowly flashing Green, constantly lit Red, quickly flashing Red, slowly flashing Red, occasionally flashing Red, constantly lit Input voltage Normal operation with battery power supply Energy-saving mode external supply via 230 VAC voltage Input voltage too high Input voltage too low Overheating Excessive load You can fasten the inverter using the holders supplied. When selecting the installation location, observe the following instructions: The inverter can be mounted horizontally or vertically. The inverter must be installed in a place that is protected from moisture. A ventilation system must be present for installations in small, closed spaces. The air intake on the underside or the air outlet on the back side of the inverter must remain clear. For ambient temperatures higher than 40 °C (such as in engine or heating compartments, or direct sunlight), the heat from the inverter under load can lead to the automatic shut-off of the inverter. Make sure you have adequate space for the cable connections underneath the device when choosing a mounting location. Note With the cable socket, you can secure the connection cable to the back side of the device. After running the cable, secure it with cable ties to the clips on the cable socket. Caution Before drilling any holes, ensure that no electrical cables or other parts of the vehicle can be damaged by drilling, sawing and filing. Fastening the inverter horizontally Clip two holders on the left bar and two on the lower right bar (fig. 5 1, page 5) with the clip over the edge on the back side of the inverter (fig. Fastening the inverter vertically Clip two holders on the left bar and two on the lower right bar (fig. 6 2, page 6) onto the cable socket, so that the edge on the back of the inverter is pinched between the wall and the clip on the cable socket. 7 1, page 6) over the fan, so that the screws fit into the screw holes. Note SinePower MSP 2012, MSP 2024, MSP 2512 and MSP 2524 are equipped with two fans. With these devices, mount an exhaust adapter in front of each fan and attach an exhaust hose. The device can only be connected by a trained professional who is familiar with the relevant VDE (German Engineering Society) regulations. This chapter is solely intended for trained professionals who are familiar with the relevant VDE (German Engineering Society) regulations!Never use the inverter on vehicles where the positive terminal of the battery is connected to the chassis. If you wish to connect more than one user to the inverter and install a socket distributor loop, you must arrange a circuit breaker (residual current circuit breaker) and set a grounding bridge in the inverter, see chapter "Connect multiple appliances" on page 48. When installed in vehicles or boats, the inverter must be connected to the chassis or earth. [. . . ] Rated input voltage Output power Peak output power Output voltage Output frequency Idle current consumption Standby current consumption Input voltage range Efficiency up to Ambient temperature for operation Ambient temperature for storage Dimensions W x D x H Weight Rated input voltage Output power Peak output power Output voltage Output frequency Idle current consumption Standby current consumption Input voltage range Efficiency up to Ambient temperature for operation Ambient temperature for storage Dimensions W x D x H Weight 8. Rated input voltage Output power Peek output power Output voltage Output frequency Idle current consumption Standby current consumption Input voltage range Efficiency up to Ambient temperature for operation Ambient temperature for storage Dimensions W x D x H Weight 2. Elément Interrupteur DIP pour le réglage du mode d'économie d'énergie Fusible Douille d'entrée 230 VCA Douille de sortie 230 VCA Borne de masse Port à distance II pour le raccordement d'une télécommande (disponible en accessoire) Port à distance pour le raccordement d'un commutateur externe permettant d'allumer et d'éteindre l'appareil. Enfichez le raccordement de la télécommande uniquement dans le port à distance II et pas dans le port à distance I. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE DOMETIC MSP 1012




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual DOMETIC MSP 1012 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.