User manual DOMETIC VHT 5200 V11-10

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual DOMETIC VHT 5200. We hope that this DOMETIC VHT 5200 user guide will be useful to you.


DOMETIC VHT 5200 V11-10: Download the complete user guide (435 Ko)

Manual abstract: user guide DOMETIC VHT 5200V11-10

Detailed instructions for use are in the User's Guide.

[. . . ] Vacuum action keeps toilet discharge line clear of effluent to prevent possible hose permeation of odor . Vacuum holding tank fittings are connected on top of the tank, eliminating the possibility of leaking due to faulty connections below the level of the tank contents . Holds three times more flushes between pump-outs than standard electric marine toilet systems . Connects to SeaLand or other tank monitor to warn when tank is nearing capacity . [. . . ] Provide additional reinforcement so that structural integrity is not compromised . · avoid (2) · possible (3) Hose and Heat Sources The operating temperature of flexible hose prohibits exposure to sources of high or direct heat, such as light bulbs or engine manifolds . If any part of the hose system must be run close to a heat source, use rigid pipe instead of hose . 6. 4 Make connections 1 . Route 1 . 5 in . /38 mm ID sanitation hose from toilet to VHT inlet, and from VHT outlet to the boat's discharge fitting(s) (see previous section for hose routing guidelines) . VHT inlet and outlet fittings swivel to allow connection from virtually any direction (fig . Route 5/8 in . /16 mm vent hose from vacuum pump discharge to vent filter or thru-hull vent fitting . Place two hose clamps on hose near each end that attaches to fittings . 4) or liquid dishwashing soap on fitting and inside ends of hose, then twist hose onto fitting . Tighten hose clamps at ends of sanitation hose with screws positioned as shown (fig . Vent hose requires only one hose clamp at each connection . 8 SailVac Vacuum Holding Tank Installation 5 . With electrical power off, make electrical connections according to the wiring schematic shown on the parts list provided with this unit . Electrical installation must follow ABYC standards and should be performed by qualified personnel only . Failure to follow the procedures above may result in vacuum leaks or inefficient flushing . If the toilet, holding tank or any components are connected to any through-hull fittings, properly installed seacocks must be installed in all piping connected to the through-hull fittings . All valves must be full-bore valves and of marine (corrosion resistant) quality . Failure to do so can result in flooding, which can cause the loss of life and property . Some marine practices and/or standards require the installation of a properly positioned ventilated (vented) loop in the discharge piping to prevent back-siphonage of seawater into the holding tank . Boat operator must know local sewage discharge regulations . 8 8. 1 Cleaning and winterizing Cleaning A small amount of water remains in vacuum holding tank at all times, so it is good practice to rinse the VHT completely after contents have been discharged . After initial pump-out, add holding tank deodorant or cleaner to toilet bowl, and flush with water . Continue flushing and pumping out tank until holding tank discharge is clear . 8. 2 Winterizing Use only propylene glycol freshwater antifreeze to winterize the holding tank . Never use ethylene glycol automotive antifreeze in freshwater systems . 9 Troubleshooting Problem Possible Cause a . Vacuum pump discharge or intake lines are plugged . 10 SailVac Vacuum Holding Tank Problem 3 . [. . . ] To obtain warranty service, first contact your local dealer from whom you purchased this product or go to http://www . dometic . com to locate a dealer near you . 11 Customer service There is a strong, worldwide network to assist in servicing and maintaining your toilet system . For the Authorized Service Center near you, please call from 8:00 a . m . You may also contact or have your local dealer contact the Parts Distributor nearest you for quick response to your replacement parts needs . Telephone: Fax: Web site: 1-800-321-9886 330-496-3211 330-496-3097 330-496-3220 U . S . A . [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE DOMETIC VHT 5200




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual DOMETIC VHT 5200 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.