User manual FLYMO HVT52

[. . . ] Tampa do depósito de combustível e parafuso da ventilação 10. Lista de Assistência Internacional PÁGINAS PORTUGUESAS (74-81) SF - SISÄLTÖ 1. SUOMALAISET SIVUT (42-49) CONTENIDO Interruptor de contacto Manillar superior Amarra Arandela Tuerca inaflojable Perno de fijación de manillar superior 7. La tapa del tanque de combustible y el tornillo del respiradero de aire. [. . . ] To reduce fire hazard, keep the engine, muffler and fuel storage area free of grass, leaves or excessive grease. Remove the bolts (C1), washers (C2) and lock nuts (C4) from the polythene bag. Place one washer (C2) on to the bolt (C1) and secure the lower handle (C4) by placing bolt (C1) through deck bracket (C5) and lower handle (C4). Place washer (C2) on bolt and secure with lock nut (C3). 5 D 4 6 2 5 2. 3. 3 E F Assembly of upper handle to lower handle (Fig D) Assemble upper handle (D5) to lower handle (D4) by fitting bolts (D6) and washers (D2) and securing with lock nuts (D3). Handle Position The handle position can be altered by moving it forward for the park position (Fig E) or back for the trimming position (Fig F). 5 Starting and Stopping Before Starting your Trimmer Filling the Fuel Tank 1. Never use stale fuel left from last season or fuel which has been stored for long periods. Refit fuel tank cap and wipe up any spilled fuel. G To Start your Trimmer 1. Set the choke control lever (H2) to 'cold start' when the engine is cold, or 'normal' when the engine is hot. Place your right foot on the deck and grasp the top of the lower handle with your left hand. A) gently until you feel a resistance, return the starting handle slowly. 10. Allow the engine to reach its full running speed then gently lower the trimmer to the ground. When the engine has warmed up make sure the choke control lever (H2) is in the 'normal' position. H 2 1 J (GB) USE K STOP - STOP START - L M To Stop your Trimmer 1. G). 6 Removing and Fitting Cutting Line Height Adjustment N q q The cutting line is sharp, wear gloves and take care when handling it. Check the cutting line frequently during use and on completion of trimming. Push the line towards the centre of the cutting disc and carefully remove. Holding the line with thumb and forefinger and using other thumb as a guide, curve around centre portion of the cutting disc (as illustrated in Fig P) and thread through the hole on the rim of the cutting disc. At all times the amount of line extending beyond the edge of disc should be of an even length. If there is a variation of more than half an inch between the four lengths of line replace immediately with four full new lengths. Removing the Cutting Line 1. P 2. Fitting the Cutting Line 1. Q 2. q R (GB) USE 6 5 4 2 1 Highest height of cut q Important:- Only fit four cutting lines at any one time. Remove bolt (R1), spring washer (R2), washer (R3) cutting disc (R4) and spacer (R5) (if fitted). Select required height of cut, (See Figs S, T, U & V) and replace any cutting lines required, ensuring that cutting line is fitted on correct side of cutting disc. 3 S 2. 3. T U q Important:- Cutting line must be on the side of the disc facing the grass when fitted. 4. Replace impeller (R6) on to engine shaft ensuring that it is correctly located. [. . . ] Certify that a sample of the above product has been tested and found to comply with directives:89/392/EEC, 89/336/EEC I, the undersigned P. Howells of Flymo/Partner, a Division of Electrolux Outdoor Products Limited, Aycliffe Industrial Estate, NEWTON AYCLIFFE, Co. Certify that a sample of the above product has been tested using directive 81/1051/EEC as a guide. The maximum A-weighted sound pressure level recorded at operator position under free field semi anechoic chamber conditions was:Type Identification of Series Level HVT52 See Product Rating Label 84. 5 dB(A) I, the undersigned P. [. . . ]