Detailed instructions for use are in the User's Guide.
[. . . ] Service Manual
DIGITAL MULTITRACKER
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU AU FOND.
The lighting flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
"WARNING"
"TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. "
SAFETY INSTRUCTIONS
1. [. . . ] You can see that the following service menus will appear on the MR16 LCD. Select one of the service menus you would like to execute and press the [MENU/ENTER] dial.
4-2. Version
In the "Version" service menu, the current MR16 software version as well as the corresponding software programming date can be checked. 1) After selecting the "Version" menu, press the [MENU/ENTER] dial to check the current software version and the programming date. The example on the right indicates that the software version is "V1. 02" the programming date is February 5th, 2007 and the CPU revision number is E2. By pressing the STOP key, MR16 returns to the service menu select condition.
4-3. Version Up
The "Version Up" service menu allows you to update the MR16 software by placing the software update file in the root directory tree of the MR16 3. 5" internal hard disk. SOFTWARE UPDATE" on page 10 in detail.
16
&
Service Manual
4-4. Advanced Format
MR16 checks the remaining capacity / partition information written on the internal HD in the bootup process after powering on. In case this information does not match the current HD condition, the "Advanced Format" service menu can be used. For example, even if no song has been created (recorded) but the remaining capacity indicates only 10MB, execute the "Advanced Format" menu. As indicated on the right, please remember that executing the "Advanced Format" deletes all the songs recorded on the internal HD.
Upon completion of "Advanced Format", the message "Boot Sector Clear" appears on the LCD. NOTE: In case MR16 is not booted up correctly and displays an alert message such as "Please Wait!" permanently, power if off once. CD-RW Disk Erase
Executing the "Disk Erase" service menu erases all existing song data on the CD-RW disk put into the MR16HD/CD internal CD-R/RW drive. 3) To go on, press the [MENU/ENTER] dial while holding down the [REC] key.
4) The CD-RW disk erasing procedures begin. It will take about one minute to complete the procedures.
5) Upon completion, "Completed!" will appear on the LCD.
17
&
Service Manual
4-6. Display Test
This menu checks if the EFFECT SEND / PAN / REVERB/DELAY pots & faders / self-illuminating tact switches are working properly. 1) After selecting the "Display Test" menu, press the [MENU/ENTER] dial.
2) Press the [MENU/ENTER] dial again. As shown in the drawing below, each value the EFFECT SEND / PAN / TO STEREO BUSS LEVEL / REVERB/DELAY pots & faders position. Rotate the EFFECT SEND / PAN pots and move the faders to check if the value changes from "0" to "F" in hexadecimal depending on the pots / fades position as follow. EFFECT SEND Pots 1 ~ 8: PAN pots 1 ~ 8: TO STEREO BUSS LEVEL pot: REVERB/DELAY pot: Channel faders (1 ~ 8, 9/10, 11/12, 13/14, 15/16): Master fader: 0 (CCW) ~ F (CW) 0 (CCW) ~ F (CW) 0 (CCW) ~ F (CW) 0 (CCW) ~ F (CW) 0 (down) ~ F (up) 0 (down) ~ F (up)
INPUT A BAL
INPUT B BAL
INPUT C BAL
INPUT D BAL
L
STEREO OUT
R
1
AUX OUT
2
UNBAL /GUITAR
INSERT
UNBAL
UNBAL
UNBAL 1 PHONES 2
POWER
TRIM DISTORTION
PEAK
TRIM
PEAK
TRIM
PEAK
TRIM
PEAK
VOLUME
MIN MAX GUITAR
LINE
MIC
LINE
MIC
LINE
MIC
LINE
MIC
MIN
MAX
INPUT A
INPUT B
INPUT C
INPUT D
TO STEREO BUSS LEVEL
MIN MAX ROOM HALL PLATE DELAY BOUNCE MODE 15/16 > STEREO WAV FILE
INPUT EQ
MIN MAX REVERB / DELAY TIME
EFFECT
BOUNCE
MENU / ENTER
POWERFUL
NATURAL
BRIGHT
TIMEBASE SELECT
STORE
UNDO/REDO
MASTERING AMP MIC SIMULATION SIMULATION EFFECT SEND
0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 AUTO PUNCH PLAY MODE A / IN B / OUT RHYTHM GUIDE CONTRAST DIRECT LOCATE
LOCATE DYNAMIC BRIT STACK
L ABC1 R L DEF2 R L GHI3 R L JKL4 R L R MNO5 L R PQR6 L STU7 R L R VWX8 YZ9 +-_0 DELETE
PAN
REC SELECT
CONDENSER US METAL
MAX 1 2 3 4 5 6 7 8 9/10 11/12 13/14 15/16 MASTER MAX
REWIND
F FWD
LOCATE ABS ZERO RECORD STOP
LOCATE REC END
PLAY
TUBE
60'S COMBO
MIN
MIN
A-B PLAY
18
&
Service Manual
3) After checking, press the [MENU/ENTER] dial to proceed the next Display Test. The next test is to check if the self-illuminating tact switches are lit in red. [. . . ] C001, 002 C003, 004 C005 C006, 007 C008, 009 C010~012 C013 C014~018 C019~021 C022 C023 C024, 025 C026, 027 C028 C029~032 C033, 034 C035~065
Part No. 8233 3221 07 8233 3224 77
CAPACITORs ALU = Electrolytic type CER = Ceramic type MFR Part No. Description 366801 366802 065549 066074 391288 065549 050117 065549 065547 366801 065549 065975 065547 065549 065549 ST, ALU, 16V, 100UF, 20%, MVY N/A ST, ALU, 16V, 470UF, 20%, MV CIPCERA, R1608, 50V, 103K, T ELECIP, MV, 16V, 100M, T ELECIP, MV, 50VC, 479M, B55, T CIPCERA, R1608, 50V, 103K, T CIPCERA, EMK212BJ474KG-T, 2125, 16V, 474K, T CIPCERA, R1608, 50V, 103K, T CIPCERA, F1608, 25V, 104Z, T ST, ALU, 16V, 100UF, 20%, MVY CIPCERA, R1608, 50V, 103K, T CIPCERA, R1608, 50V, 471K, T CIPCERA, F1608, 25V, 104Z, T CIPCERA, R1608, 50V, 103K, T N/A CIPCERA, R1608, 50V, 103K, T
8233 3221 07
Ref. 8245 8245 8245 8553 8253 8553 8553 2720 2720 8230 0060 4720 0060 0060 30 17 35 01 02 01 01
MISCELLANEOUS MFR Part No. [. . . ]