User manual FRIGIDAIRE FPIF3093LF SERVICE DATASHEET
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual FRIGIDAIRE FPIF3093LF. We hope that this FRIGIDAIRE FPIF3093LF user guide will be useful to you.
You may also download the following manuals related to this product:
FRIGIDAIRE FPIF3093LF DATASHEET (647 ko)
Manual abstract: user guide FRIGIDAIRE FPIF3093LFSERVICE DATASHEET
Detailed instructions for use are in the User's Guide.
[. . . ] SERVICE DATA SHEET
Electric Range with ES 540 Electronic Oven Control
NOTICE - This service data sheet is intended for use by persons having electrical and mechanical training and a level of knowledge of these subjects generally considered acceptable in the appliance repair trade. The manufacturer cannot be responsible, nor assume any liability for injury or damage of any kind arising from the use of this data sheet. SAFE SERVICING PRACTICES To avoid the possibility of personal injury and/or property damage, it is important that safe servicing practices be observed. [. . . ] If fault code is present with cold oven test oven temperature sensor probe circuit resistance. If temperature sensor probe circuit is good but fault code remains when oven is cold replace the EOC. If oven is severely overheating/heating when no cook cycle is programmed test oven temperature sensor probe circuit resistance using the RTD scale found in the service tech sheet. Also verify that the temperature sensor probe in properly installed in the oven cavity. If oven continues to heat when the power is reapplied, replace the EOC. NOTE: Severe overheating may require the entire oven to be replaced should damage be extensive. Reset power supply to range - Disconnect power, wait 30 seconds and reapply power. If keyboard ciruits check good replace the EOC.
F11
Shorted keypad or selector switch.
4.
F12 F13 F14
EOC Internal software error or failure. Membrane switch tail missing or not connected Communication failure between EOC & ESEC system Open oven sensor probe circuit. Door lock motor or latch circuit failure.
Disconnect power, wait 30 seconds and reapply power. Check/reseat connections between membrane switch, display boards and EOC. (F30) Check resistance at room temperature & compare to RTD Sensor resistance chart. (F31) Check resistance at room temperature, if less than 500 ohms, replace RTD Sensor Probe. Check for shorted Sensor Probe harness between EOC & Probe connector. [. . . ] Press the Self Clean keypad to change the sign of the adjustment to a (-) if necessary. Once the desired adjustment (-35° to 35° F) has been entered, press the Start keypad to accept the change or the Cancel keypad to reject the change. The adjustments made will not change the self-cleaning temperature.
F20
F30 F31 F90 F91 F92 F93 F94 F95
Electronic Oven Control & Jumper Connections (EOC Rear View)
Circuit Analysis Matrix
Resistance Temperature Detector (RTD)
Resistance Temperature Detector Scale
RTD SCALE Temperature (°F) 32 ± 1. 9 Resistance (ohms) 1000 ± 4. 0 1091 ± 5. 3 1453 ± 8. 9 1654 ± 10. 8 1852 ± 13. 5 2047 ± 15. 8 2237 ± 18. 5 2697 ± 24. 4
IMPORTANT
DO NOT REMOVE THIS BAG OR DESTROY THE CONTENTS
WIRING DIAGRAMS AND SERVICE INFORMATION ENCLOSED
75 ± 2. 5 250 ± 4. 4 350 ± 5. 4 450 ± 6. 9 550 ± 8. 2 650 ± 9. 6 900 ± 13. 6
REPLACE CONTENTS IN BAG
p/n 316904436 (1007)
General Troubleshooting Diagram
General Troubleshooting Schematic [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE FRIGIDAIRE FPIF3093LF
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual FRIGIDAIRE FPIF3093LF will begin.