User manual HONEYWELL MAGICSTAT 34
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual HONEYWELL MAGICSTAT 34. We hope that this HONEYWELL MAGICSTAT 34 user guide will be useful to you.
You may also download the following manuals related to this product:
HONEYWELL MAGICSTAT 34 (332 ko)
Manual abstract: user guide HONEYWELL MAGICSTAT 34
Detailed instructions for use are in the User's Guide.
[. . . ] AND CANADA
Savings for Once-A-Day 10°F (5°C) decrease 30% Approximate percentage of energy cost savings 28% 26% 24% 22% 20% 18% 16% 14% 12% 10% 8% 6% 4% 2%
Minneapolis St. Paul Montreal Ottawa Toronto Edmonton Regina Winnipeg Calgary Moncton North Bay Quebec St. John's Halifax Vancouver Buffalo Cleveland Milwaukee Denver Des Moines Omaha Salt Lake City Boston Chicago Detroit Pittsburgh Indianapolis Cincinnati Kansas City St. Louis Columbus Louisville New York Philadelphia Portland Wash. , D C Seattle San Francisco Dallas Atlanta Los Angeles San Diego
Savings for Twice-A-Day 10°F (5°C) decrease*
*Based on 10°F (5°C) decrease--(5°F [3°C] decrease gives approximately 55 percent of these savings).
J. S. [. . . ] (This will be a higher temperature during heating season, or a lower temperature during cooling season. ) DAYTIME is the time period you can set for an energy-saving temperature while you are away at work or school. (This will be a lower temperature during heating season, or a higher temperature during cooling season. ) EVENING is the time period you want the house at a comfortable temperature for activities before bedtime. (Again, higher heat or lower cool. ) NIGHT is the time period you can set for an energy-saving temperature while you are sleeping. Although for more comfortable sleeping, some people choose not to raise the cool temperature during the night. )
9 69-0733--3
After the batteries are installed, the thermostat can be easily programmed in your hand before it is installed on the wall. NOTE: The factory-preprogrammed time and temperature settings are shown in parentheses.
PROGRAMMING
12
69-0733--3
When programming your new thermostat, use this guide. SET PRESENT DAY Set Press and release Day/Time Present SET PRESENT TIME Set Press and release Day/Time Present then then until present day shows.
a
Time
Day
until present time shows. Use
a
Time
HEATING PROGRAM With system switch at HEAT, press and release
a
Morning
and
Temp
to
program Mon-Fri MORNING time and temperature. Press and release
Morning
; use
a
Time
and
to program Saturday morning time and temperature. Repeat steps as you did for SAT.
13 69-0733--3
COOLING PROGRAM The times you set for heating remain the same for cooling; you only need to program the temperatures. Press and release
Morning
; use
Temp
a
to
Saturday morning temperature. Repeat steps as you did for SAT.
After programming, adjust fan and system switches as desired. to move number ahead.
69-0733--3
Press on
to move number back; press on
14
PROGRAMMING
For operating or making changes, use this guide.
a
Temp Temporarily Change temperature for current period only-- ; TEMPORARY indicator shows on display, and cancels itself at next scheduled change. To cancel sooner, you may Run press Program .
a
Hold a temperature indefinitely (such as on vacation)-- Run on display; to cancel, press Program . Check current temperature setting--
Current Setting
Hold Temp
,
Temp
Hold appears
.
Evening
Cancel a program--Press and hold , Morning cannot be cancelled (only changed).
Daytime
or
Night
three seconds to cancel.
Permanently Change a program--Repeat steps under Heating Program (page 13) or Cooling Program (page 14), as applicable. Return to normal program or start program--
a
Run Program
.
Press on
to move number back; press on
15
to move number ahead.
69-0733--3
STEP 5 Mount Thermostat Wallplate
s Position wallplate on wall. Use a pencil to mark the two mounting holes that best fit the application.
WALL
WIRES THROUGH WALL OPENING
WALL ANCHORS (2) MOUNTING 1 HOLES (3) MOUNTING SCREWS (2) WALLPLATE 1 USE THE TWO MOUNTING HOLES THAT BEST FIT APPLICATION.
M5932A
16
69-0733--3
INSTALLATION
s Remove wallplate from wall, and drill 3/16 inch holes in wall (if drywall) as marked. Gently tap anchors (provided) into drilled holes until flush with the wall. s Reposition wallplate over holes, pulling wires through wiring opening. s Level for appearance only; thermostat functions properly even when not level. Tighten mounting screws.
LEVEL
M611B
17
69-0733--3
STEP 6 Adjust System On-Time, Clock Display, As Required
s The thermostat on-time is factory-set for a warm air, gas or oil heating system. If you are installing it on another type of system, the ontime must be adjusted accordingly by setting screws 1A and 1B on the back of the thermostat, using the heating system table in the illustration as a guide. The system on-time should be optimized with the type of system to minimize room temperature swings. [. . . ] The thermostat's current setting does not match the display temperature to within ± 1°. Incorrect room temperature showing on thermostat display.
s Allow time for the furnace to heat up and the fan to come on before checking for heat at the register. Note that on most gas and oil systems, the fan is not controlled by the thermostat, but by another control, which may account for the delay. s s s Check that the wiring hole in the wall behind the wallplate has been plugged with insulation to prevent drafts that might adversely affect thermostat operation. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE HONEYWELL MAGICSTAT 34
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual HONEYWELL MAGICSTAT 34 will begin.