Detailed instructions for use are in the User's Guide.
[. . . ] T7516A, B, C Energy Management System
USER'S GUIDE
Weekday/Weekend 7-day Programmable Heat and/or Cool Conventional and Heat Pump
1
69-1611
Welcome to the world of comfort and energy savings with your new Honeywell T7516A, B, C Energy Management Thermostat brought to you by your energy utility. You can set the thermostat to control the temperature in your home, your water heater, and another appliance (such as a swimming pool pump) according to your personal schedule and preferences. Besides being programmable, this thermostat contains a communications module that allows your energy utility to communicate with your thermostat so you can take advantage of Residential Service Variable Price (RSVP) Rate. The T7516A, B, C Energy Management Thermostat informs you of the energy price in effect at any given time (see Fig. [. . . ] The Low price always uses whatever schedule programming exists and it is the basis for the offsets. The one exception is the water heater, which is always enabled during the low price.
69-1611
CAUTION
Equipment Damage Hazard. Use of sharp fingernails or pencil points can damage the keypad beyond repair. Use the ball of your finger or a soft pencil eraser when pressing the keys. IMPORTANT When programming for the appliance, make certain that you consider potential safety issues; for example: with a pool pump during winter freezing weather, you will have to operate the pool pump as you have always done to prevent pump and pipe freezing.
NOTE: Before programming the thermostat, remove the clear protective plastic display overlay.
Entering Schedule Programming
Refer to your Personal Programming Charts and proceed as follows: IMPORTANT The thermostat registers all programming inputs immediately and maintains them until manually changed. Low batteries or power outages do not delete thermostat programming.
18
69-1611
NOTE: When setting a program time or temperature, the instructions direct you to "Press and hold until the display shows the desired time (or temperature). " This changes the setting quickly in the selected direction. Use this method when the change is large (for example, two hours, or ten degrees). Once the setting is close, press and release the key to move the setting one step at a time. Inputting Basic Program The most efficient way to program the thermostat is to first input a basic program for the entire week. Then, you can make changes to specific days to fit your needs.
IMPORTANT Because this procedure can affect up to seven days of programming, be careful when making changes with multiple days selected. NOTES: -- If you delete all programming with the CLEAR key, the thermostat uses the default program. -- PGM is an indication that you are in programming mode.
19
69-1611
Step 1: Setting Basic Cooling Times and Temperatures.
First program the MORN time and temperature, if desired, for the entire week.
Device
Press and release until the display shows PGM COOL.
AM
M15403
Day of
Week
Press and release until the display shows MON TUE WED THU FRI SAT SUN. Press and release until the display shows MORN.
AM
M15403
Time
AM
Period
M15403
20
69-1611
Ahead Back
Press and hold until the display shows the desired time.
AM
M15404
Warmer Cooler
Press and hold until the display shows the desired temperature.
AM
M15405
21
69-1611
Program the DAY time and temperature, if desired, for the entire week.
Time
Period
Press and release until the display shows DAY.
M15406
Ahead Back
Press and hold until the display shows the desired time.
AM
M15407
Warmer Cooler
Press and hold until the display shows the desired temperature.
AM
M15408
22
69-1611
Program the EVE time and temperature, if desired, for the entire week.
Time
Period
Press and release until the display shows EVE.
M15409
Ahead Back
Press and hold until the display shows the desired time.
PM
M15410
Warmer Cooler
Press and hold until the display shows the desired temperature.
PM
M15411
23
69-1611
Program the NIGHT time and temperature, if desired, for the entire week.
Time
Period
Press and release until the display shows NIGHT.
M15412
Ahead Back
Press and hold until the display shows the desired time.
PM
M15413
Warmer Cooler
Press and hold until the display shows the desired temperature.
PM
M15414
24
69-1611
Step 2: Setting Basic Heating Times and Temperatures.
First program the MORN time and temperature, if desired, for the entire week.
Device
Press and release until the display shows PGM HEAT.
M15415
Day of
Week
Press and release until the display shows MON TUE WED THU FRI SAT SUN.
M15415
Time
Period
Press and release until the display shows MORN.
AM
M15416
25
69-1611
Ahead Back
Press and hold until the display shows the desired time.
AM
M15417
Warmer Cooler
Press and hold until the display shows the desired temperature.
AM
M15418
26
69-1611
Program the DAY time and temperature, if desired, for the entire week.
Time
Period
Press and release until the display shows DAY.
M15419
Ahead Back
Press and hold until the display shows the desired time.
AM
M15420
Warmer Cooler
Press and hold until the display shows the desired temperature.
AM
M15421
27
69-1611
Program the EVE time and temperature, if desired, for the entire week.
Time
Period
Press and release until the display shows EVE.
M15422
Ahead Back
Press and hold until the display shows the desired time.
PM
M15423
Warmer Cooler
Press and hold until the display shows the desired temperature.
PM
M15424
28
69-1611
Program the NIGHT time and temperature, if desired, for the entire week.
Time
Period
Press and release until the display shows NIGHT.
PM
M15425
Ahead Back
Press and hold until the display shows the desired time.
PM
M15425
Warmer Cooler
Press and hold until the display shows the desired temperature.
PM
M15426
29
69-1611
Step 3: Setting Basic Water Times and On/Off Settings.
First program the MORN time and on/off setting, if desired, for the entire week.
Device
Press and release until the display shows PGM WATER. Press and release until the display shows MON TUE WED THU FRI SAT SUN.
PM
M15427
Day of
Week
PM
M15427
Time
Period
Press and release until the display shows MORN.
AM
M15428
30
69-1611
Ahead Back
Press and hold until the display shows the desired time.
AM
M15429
Water On-Off-Clr
Press and release until the display shows the desired on/off setting.
AM
M15429
31
69-1611
Program the DAY time and on/off setting, if desired, for the entire week.
Time
Period
Press and release until the display shows DAY.
M15430
Ahead Back
Press and hold until the display shows the desired time.
AM
M15431
Water On-Off-Clr
Press and hold until the display shows the desired on/off setting.
AM
M15431
32
69-1611
Program the EVE time and on/off setting, if desired, for the entire week.
Time
Period
Press and release until the display shows EVE.
M15432
Ahead Back
Press and hold until the display shows the desired time.
PM
M15433
Water On-Off-Clr
Press and hold until the display shows the desired on/off setting.
PM
M15433
33
69-1611
Program the NIGHT time and on/off setting, if desired, for the entire week.
Time
Period
Press and release until the display shows NIGHT.
PM
M15434
Ahead Back
Press and hold until the display shows the desired time.
PM
M15434
Water On-Off-Clr
Press and hold until the display shows the desired on/off setting.
PM
M15434
34
69-1611
Step 4: Setting Basic Appliance Times and On/Off Settings.
First program the MORN time and on/off setting, if desired, for the entire week.
Device
Press and release until the display shows PGM APPL.
PM
M15443
Day of
Week
Press and release until the display shows MON TUE WED THU FRI SAT SUN. Press and release until the display shows MORN.
PM
M15443
Time
AM
Period
M15436
35
69-1611
Ahead Back
Press and hold until the display shows the desired time.
AM
M15437
Appl On-Off-Clr
Press and hold until the display shows the desired on/off setting.
AM
M15437
36
69-1611
Program the DAY time and on/off setting, if desired, for the entire week.
Time
Period
Press and release until the display shows DAY.
M15438
Ahead Back
Press and hold until the display shows the desired time.
AM
M15439
Appl On-Off-Clr
Press and hold until the display shows the desired on/off setting.
AM
M15439
37
69-1611
Program the EVE time and on/off setting, if desired, for the entire week.
Time
Period
Press and release until the display shows EVE.
M15440
Ahead Back
Press and hold until the display shows the desired time.
PM
M15441
Appl On-Off-Clr
Press and hold until the display shows the desired on/off setting.
PM
M15441
38
69-1611
Program the NIGHT time and on/off setting, if desired, for the entire week.
Time
Period
Press and release until the display shows NIGHT.
M15442
Ahead Back
Press and hold until the display shows the desired time.
PM
M15443
Appl On-Off-Clr
Press and hold until the display shows the desired on/off setting.
PM
M15443
Changing Parts of the Program After you input the basic program for the entire week, make changes to specific days to tailor the program to fit your needs.
39
IMPORTANT Because this procedure can affect up to seven days of programming, be careful when making changes with multiple days selected.
69-1611
Step 5: Changing Individual Cooling Times and Temperatures. The following example illustrates modifying the Sunday Morning Cooling program.
First, select COOL, and the desired day and period for the change.
Device
Press and release until the display shows PGM COOL.
PM
M15414
Day of
Week
Press and release until the display shows the desired day(s). Press and release until the display shows the desired period.
PM
M15445
Time
AM
Period
M15444
40
69-1611
Adjust the time that the period begins.
Ahead Back
Press and hold until the display shows the desired time.
AM
M15446
Warmer Cooler
Press and hold until the display shows the desired temperature.
AM
M15448
OR Delete the programming from the period for the days shown on the display. Press and release.
Clear
M15447
41
69-1611
Step 6: Changing Individual Heating Times and Temperatures. The following example illustrates modifying the Saturday Day Heating program.
First, select HEAT, and the desired day and period for the change.
Device
Press and release until the display shows PGM HEAT.
PM
M15426
Day of
Week
Press and release until the display shows the desired day(s). Press and release until the display shows the desired period.
AM
M15449
Time
AM
Period
M15450
42
69-1611
Adjust the time that the period begins.
Ahead Back
Press and hold until the display shows the desired time.
M15451
Warmer Cooler
Press and hold until the display shows the desired temperature.
M15452
OR Delete the programming from the period for the days shown on the display. Press and release.
Clear
M15453
43
69-1611
Step 7: Changing Individual Water Times and On/Off Settings. The following example illustrates modifying the Saturday Evening Water program.
First, select WATER, and the desired day and period for the change.
Device
Press and release until the display shows PGM WATER. [. . . ] · Your energy utility periodically resets the clock to the correct time. This can change the time more than one minute (see Replacing the Batteries section). · If condition persists for more than one minute, the thermostat cannot establish the communication link; contact your energy utility.
Clock occasionally changes more than one minute at a time. Thermostat displays: "bUSY".
65
69-1611
Personal Programming Charts
Table 3. [. . . ]