User manual HONEYWELL TD2400
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual HONEYWELL TD2400. We hope that this HONEYWELL TD2400 user guide will be useful to you.
You may also download the following manuals related to this product:
HONEYWELL TD2400 (211 ko)
Manual abstract: user guide HONEYWELL TD2400
Detailed instructions for use are in the User's Guide.
[. . . ] Programmable Thermostat
by Duracraft
OWNER'S GUIDE
Weekday/Weekend (5-day/ 2-day) Programmable Heat and/or Cool Low Voltage (20 to 30 Vac) Thermostat and Mounting Plate Model TD2400
1
69-1120
Welcome to the world of comfort and energy savings with your new Duracraft Programmable Thermostat. Your new thermostat will automatically control the temperature in your home, keeping you comfortable while saving energy when programmed according to the instructions in this manual. Direct any questions concerning the application of this thermostat to Duracraft Consumer Services at 1-800-554-4558, Monday-Friday 7:00 a. m. -5:30 p. m. , Eastern time.
RECYCLING THERMOSTAT
If this thermostat is replacing a thermostat that contains mercury in a sealed tube, do not place your old thermostat in the trash. Contact your local waste management authority for instructions regarding recycling and the proper disposal of your old thermostat. [. . . ] If you make an error at any time during programming, just press the Run Program key, and continue again at the step where you left off.
69-1120
Personal Programming Chart
Weekdays WAKE LEAVE RETURN SLEEP Weekendsb WAKE SLEEP
aThe temperatures cannot be set any higher than 88°F (31°C) or any lower than 45°F (7°C). bIf you decide not to enter weekend programs, the SLEEP from the weekday program will copy to
Heating Program Start Time
Heating Temperaturea
the weekend schedule.
12
69-1120
Weekdays WAKE LEAVE RETURN SLEEP Weekendsb WAKE SLEEP
Cooling Program Start Time
Cooling Temperaturea
aThe temperatures cannot be set any higher than 88°F (31°C) or any lower than 45°F (7°C). bIf you decide not to enter weekend programs, the SLEEP from the weekday program will copy to
the weekend schedule. NOTE: If you decide not to program the thermostat, it will automatically control heating at 68°F (20°C), and cooling at 78°F (26°C), 24 hours a day.
13 69-1120
This guide can be used for programming your new thermostat. Remove battery door (on thermostat left side) using a coin at the bottom. Also note that the label inside the battery cover contains an abbreviated set of programming procedures for the thermostat.
Set Current Time/Day
Clock/Day
Time Clock/Day
To set time, press and release press and release again, press
once, press
Time
until current time shows. To set day,
Run Program
until current day shows; then press
.
Heating Program
With System switch at Heat, press and release SET appear on display.
Weekday
once. Adjust Fan Operation Switch, As Required
u The thermostat fan operation switch, labeled FUEL SWITCH (see illustration on page 19) is factory-set in the F position. The E setting will allow the fan to turn on immediately with the heating or cooling in a system where the G terminal is connected.
Step 6. Adjust System On-Time, °F/°C, As Required
u The thermostat on-time is factory-set for a warm air, gas or oil heating system. If you are installing it on another type of system, adjust the on-time accordingly by setting screws A and B on the back of the thermostat. use the heating system table shown in the illustration (page 19) as a guide. The system on-time should be optimized according to the type of system to minimize room temperature swings. Setting the screw "out one turn" means turning the screw approximately 360° counterclockwise, or about one complete turn. In the unlikely event that you want a longer furnace on-time, readjust screws A and/or B as follows:
18
69-1120
First, turn in both screws completely, then adjust for system type: · Warm Air Furnace--Set at the Hot Water setting (A--out one turn, B--leave in). · Electric Furnace--Leave at the Warm Air Furnace setting (A--leave in, B--leave in). IMPORTANT When using a high efficiency furnace such as a 90% or greater AFUE (Average Fuel Utilization Efficiency) unit, adjust screw A out one turn and leave screw B in.
19
u The thermostat is set to read the temperature in degrees Fahrenheit. If readings are desired in degrees Celsius, adjust screw C out one turn, as shown in illustration.
THERMOSTAT BACK
A
DISPLAY °F CIN DISPLAY °C COUT 1 TURN
C
ADJUST SCREWS THROUGH HOLES TO SELECT OPERATION DESIRED FUEL SWITCH HEATING SYSTEM POSITION F WARM AIR AIN BIN FURNACE F HOT WATER AOUT BIN BOILER 1 TURN E ELECTRIC AIN BOUT FURNACE 1 TURN
B
D
W
FOR HIGH EFFICIENCY FURNACE (90%+ AFUE) ADJUST: SCREW AOUT ONE TURN SCREW BIN FUEL SWITCH F POSITION
Y
G
FUEL SWITCH
F
E
R
Rc
M8796
69-1120
Step 7. u Remove mounting plate from wall, and drill 3/16-inch holes in wall (if drywall) as marked. For firmer material such as plaster or wood, drill WALL ANCHORS (2) WIRES THROUGH 7/32-inch WALL OPENING holes. Gently WALL tap anchors (provided) into drilled holes MOUNTING PLATE until flush with the wall.
MOUNTING SCREWS (2)
M1718
u Reposition mounting plate over holes, pulling wires through wiring opening. u Level for appearance only; thermostat will function properly even when not level. [. . . ] Check that the wiring hole in the wall behind the wallplate has been plugged with insulation to prevent drafts that might adversely affect thermostat operation. Be aware that it is normal for the current setting and display temperature to differ on occasion. During recovery from setback or setup, setting and display temperatures may differ for up to 30 minutes after recovery period.
33
69-1120
Incorrect room temperature showing on thermostat display.
Make sure the hole behind the thermostat is plugged with insulation to help prevent drafts from adversely affecting the thermostat operation. The thermostat is factory-calibrated and cannot be adjusted.
Toll-free Customer Assistance
For all questions concerning this thermostat, please read and follow the instructions. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE HONEYWELL TD2400
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual HONEYWELL TD2400 will begin.