Detailed instructions for use are in the User's Guide.
[. . . ] INSTRUCTION MANUAL
VHF/UHF DUAL BAND FM TRANSCEIVER
iE7
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIO TELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW.
FOREWORD
Thank you for purchasing this Icom product. The IC-E7 VHF/UHF DUAL BAND FM TRANSCEIVER is designed and built with Icom's superior technology and craftsmanship. [. . . ] · If "OFF" appears, check the offset frequency (see p. qSet the receive frequency, or shift direction (see p. 19 for details. ). to transmit a 1750 Hz tone burst signal.
· The displayed frequency automatically changes to the transmit frequency (repeater input frequency). · If "OFF" appears, check the offset frequency (see p. 20 for details) or shift direction (p. 19).
then
SCAN
SCAN
S. MW
S. MW
SET
SET
SET
rPush and hold [PTT] to transmit. yPush and hold [SQL] (ATT·SET) to monitor the repeater input frequency.
ePush and hold [PTT] to transmit. tPush and hold [SQL] (ATT·SET) to monitor the repeater input frequency.
23
MEMORY/CALL CHANNELS
General description
The IC-E7 has 1050 memory channels including 50 scan edge memory channels (25 pairs) for storage of often-used frequencies. And a total of 18 memory banks, A to H, J, L, N, O to R, T, U and Y are available for storing groups of frequencies, etc. Up to 100 channels can be assigned into a bank.
6
Memory channel programming
q Push [V/M] (SKIP·S. MW) to select VFO mode. w Set the desired frequency: Select the desired band with [BAND] (TS·LOCK). offset frequency, duplex direction, subaudible tone frequency, etc. ), if desired. to enter select memory write mode.
· 1 short and 1 long beep sound. ·" " indicator and memory channel number blink.
D Memory channel contents
The following information can be programmed into memory channels: · Operating frequency (p. 14) · Duplex direction (DUP or DUP) with an offset frequency (pgs. 39).
5 6
r Rotate [DIAL] to select the desired channel.
· Call channels (C0, C1), VFO (VF) and scan edge channels (00A/00b to 24A/24b), as well as regular memory channels, can be programmed in this way. · While pushing and holding [FUNC], rotate [DIAL] to select memory channel in 10 channel steps.
t Push and hold [V/M] (SKIP·S. MW) for 1 sec.
· 3 beeps sound · Memory channel number automatically increases when continuing to push [V/M] (SKIP·S. MW) after programming.
[EXAMPLE]: Programming 439. 370 MHz into memory channel 20 (blank channel).
Push
WFMAM -DUP T SQL
S. MW
for 1 sec.
WFMAM -DUP T SQL
Rotate
DTCS ATT
WFMAM -DUP T SQL
Push
DTCS ATT
S. MW
for 1 sec.
WFMAM -DUP T SQL
DTCS ATT
DTCS ATT
WFMAM -DUP T SQL
DTCS ATT
VOL PRIO P SKIP MR 9 5 LOW 1
VOL PRIO P SKIP MR 9 5 LOW 1
VOL PRIO P SKIP MR 9 5 LOW 1
VOL PRIO P SKIP MR 9 5 LOW 1
VOL PRIO P SKIP MR 9 5 LOW 1
24
6
MEMORY/CALL CHANNELS
Memory bank setting
The IC-E7 has a total of 18 banks (A to H, J, L, N, O to R, T, U and Y). Regular memory channels, 000 to 999, may assigned into a desired bank for easy memory management. to enter select memory write mode.
· 1 short and 1 long beep sound. ·" " indicator and memory channel number blink.
rWhile pushing and holding [BAND] (TS·LOCK), rotate [DIAL] to select the desired bank.
· Banks A to H, J, L, N, O to R, T, U and Y are available. · The bank can also be selected by pushing [BAND] (TS·LOCK) several times. Bank is selected with
WFMAM -DUP T SQL
+
w Rotate [DIAL] to select the desired memory channel. eWhile pushing and holding [CALL] (MODE·SCAN), rotate [DIAL] to select "BANK. "
· After releasing [CALL] (MODE·SCAN), "-- -- -- --" is displayed instead of the frequency indication, and only " " indicator blinks. [. . . ] Tuning step selection While pushing and holding [FUNC], push [BAND] to enter tuning step selection. Then rotate [DIAL] to select the desired tuning step.
· Push [BAND] again to return to the previous condition.
Frequency setting q Push [V/M] to select VFO mode. w Rotate [DIAL] to set the desired operating frequency.
· While pushing [FUNC], dial rotation changes frequency in 1 MHz steps.
1750 Hz tone burst Push [PTT] briefly, then push and hold [PTT] again for 1 to 2 sec. Set mode setting q While pushing and holding [FUNC], push and hold [SQL] for 1 sec. [. . . ]