User manual ICOM IC-P7A
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual ICOM IC-P7A. We hope that this ICOM IC-P7A user guide will be useful to you.
Manual abstract: user guide ICOM IC-P7A
Detailed instructions for use are in the User's Guide.
[. . . ] INSTRUCTION MANUAL
VHF/UHF DUAL BAND FM TRANSCEIVER
iP7A
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIO TELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW.
FOREWORD
Thank you for purchasing this Icom product. The IC-P7A VHF/UHF DUALBAND FM TRANSCEIVER is designed and built with Icom's superior technology and craftsmanship. [. . . ] qWhile pushing and holding [FUNC], push and hold [SQL] (ATT·SET) for 1 sec. to enter set mode.
[DIAL] · OFF · DUP ONLY · DUP TONE · OFF · ON
USA/KOREA versions only eWhile pushing and holding [FUNC], rotate [DIAL] to select the desired condition. (default)
Korea version:
r Push [SQL] (ATT·SET) to exit set mode.
D Frequency range and offset direction
· U. S. A. version: Frequency range
SCAN
Duplex direction "" appears "+" appears "+" appears "" appears
S. MW
145. 200145. 495 MHz 146. 610146. 995 MHz 147. 000147. 395 MHz 442. 000444. 995 MHz
DTCS ATT
SET
SET
wRotate [DIAL] to select "AUTORP. "
WFMAM -DUP T SQL
DTCS ATT
WFMAM -DUP T SQL
447. 000449. 995 MHz · Korea version: Frequency range 439. 000440. 000 MHz
VOL PRIO P SKIP MR 9 5 LOW 1
After 1 sec.
VOL PRIO P SKIP MR 9 5 LOW 1
Auto repeater item
Setting indication
Duplex direction "" appears
23
MEMORY/CALL CHANNELS
General description
The IC-P7A has 1050 memory channels including 50 scan edge memory channels (25 pairs) for storage of often-used frequencies. And a total of 18 memory banks, A to H, J, L, N, O to R, T, U and Y are available for storing groups of frequencies, etc. Up to 100 channels can be assigned into a bank.
6
Memory channel programming
q Push [V/M] (SKIP·S. MW) to select VFO mode. w Set the desired frequency: Select the desired band with [BAND] (TS·LOCK). offset frequency, duplex direction, subaudible tone frequency, etc. ), if desired. to enter select memory write mode.
· 1 short and 1 long beep sound. ·" " indicator and memory channel number blink.
D Memory channel contents
The following information can be programmed into memory channels: · Operating frequency (p. 14) · Duplex direction (DUP or DUP) with an offset frequency (pgs. 39).
5 6
r Rotate [DIAL] to select the desired channel.
· Call channels (C0, C1), VFO (VF) and scan edge channels (00A/00b to 24A/24b), as well as regular memory channels, can be programmed in this way. · While pushing and holding [FUNC], rotate [DIAL] to select memory channel in 10 channel steps.
t Push and hold [V/M] (SKIP·S. MW) for 1 sec.
· 3 beeps sound · Memory channel number automatically increases when continuing to push [V/M] (SKIP·S. MW) after programming.
[EXAMPLE]: Programming 145. 870 MHz into memory channel 20 (blank channel).
Push
WFMAM -DUP T SQL
S. MW
for 1 sec.
WFMAM -DUP T SQL
Rotate
DTCS ATT
WFMAM -DUP T SQL
Push
DTCS ATT
S. MW
for 1 sec.
WFMAM -DUP T SQL
DTCS ATT
DTCS ATT
WFMAM -DUP T SQL
DTCS ATT
VOL PRIO P SKIP MR 9 5 LOW 1
VOL PRIO P SKIP MR 9 5 LOW 1
VOL PRIO P SKIP MR 9 5 LOW 1
VOL PRIO P SKIP MR 9 5 LOW 1
VOL PRIO P SKIP MR 9 5 LOW 1
24
6
MEMORY/CALL CHANNELS
Memory bank setting
The IC-P7A has a total of 18 banks (A to H, J, L, N, O to R, T, U and Y). Regular memory channels, 000 to 999, may assigned into a desired bank for easy memory management. to enter select memory write mode.
· 1 short and 1 long beep sound. ·" " indicator and memory channel number blink.
rWhile pushing and holding [BAND] (TS·LOCK), rotate [DIAL] to select the desired bank.
· Banks A to H, J, L, N, O to R, T, U and Y are available. · The bank can also be selected by pushing [BAND] (TS·LOCK) several times. Bank is selected with
WFMAM -DUP T SQL
+
w Rotate [DIAL] to select the desired memory channel. eWhile pushing and holding [CALL] (MODE·SCAN), rotate [DIAL] to select "BANK. "
· After releasing [CALL] (MODE·SCAN), "-- -- -- --" is displayed instead of the frequency indication, and only " " indicator blinks. · Bank group and channel number is displayed if the selected memory channel has already been assigned to a bank. · "BANK" can can also be selected by pushing [CALL] (MODE·SCAN) several times. [DIAL]
WFMAM -DUP T SQL
DTCS ATT
VOL PRIO P SKIP MR 9 5 LOW 1
t Rotate [DIAL] to select the desired bank channel number.
· Vacant bank channel numbers are only be displayed. [. . . ] NOTE: Connect the HM-153P after removing the [MIC/SP] cap (MIC/SP jack cover). Keep the [MIC/SP] cap attached when jack are not in use to keep the contact clean.
OPC-782 Microphone Microphone
HM-153 Speaker/MIC connector
HM-153P
15
SCAN SCAN
S. MW S. MW
SET
SET
78
15
OPTIONS
D LC-161 CARRYING CASE
Helps protect the transceiver from scratches, etc. NOTE: When using as below illustration, tension release loop protects the [MIC/SP] connector from being damaged by cable stress or vibration OPC-782 HM-128
D HM-128 EARPHONE MICROPHONE
An optional OPC-782 is required for connection.
q w
Transceiver
D HM-131 SPEAKER MICROPHONE
An optional OPC-782 is required for connection. HM-131 LC-161 Tension release loop
e
79
POCKET GUIDE
Important operating instructions are summed up in this and the following page for your simple reference. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE ICOM IC-P7A
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual ICOM IC-P7A will begin.