User manual ICOM IC-R5
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual ICOM IC-R5. We hope that this ICOM IC-R5 user guide will be useful to you.
You may also download the following manuals related to this product:
ICOM IC-R5 BROCHURE (162 ko)
ICOM IC-R5 1 (20 ko)
ICOM IC-R5 BROCHURE 2 (362 ko)
ICOM IC-R5 INSTRUCTION MANUAL (2998 ko)
ICOM IC-R5 SUPPLEMENTARY GUIDE (20 ko)
Manual abstract: user guide ICOM IC-R5
Detailed instructions for use are in the User's Guide.
[. . . ] INSTRUCTION MANUAL
COMMUNICATIONS RECEIVER
iR5
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FOREWORD
Thank you for purchasing this Icom product. The IC-R5 COMMUNICATIONS RECEIVER is designed and built with Icom's superior technology and craftsmanship. With proper care, this product should provide you with years of trouble-free operation. [. . . ] 26)
Band edge Scan edges xxA Scan Jump Band xxB edge
MEMORY (SKIP) SCAN
(p. 28)
SKIP
M1 M0 M 199 M6 M5 M2 M3 M4
SKIP
Repeatedly scans memory channels except those set as skip channels. Skip channels can be turned ON and OFF by pushing [FUNC] + [V/M·S. MW·~] in memory mode. Skips unwanted frequencies or channels that inconveniently stop scanning. This function can be turned ON and OFF by pushing [FUNC] + [V/M·S. MW·~] in either VFO or memory mode.
ALL/SELECTED BANK SCAN (p. 28)
SKIP
A00 A99 A98 A05 A04 A01 A02 A03
Repeatedly scans all bank channels or selected bank channels. The skip scan is also available.
FREQUENCY/MEMORY SKIP FUNCTION (p. 30)
Band edge Scan SKIP Jump SKIP Band edge
SKIP
25
SCAN OPERATION
6
I Full/band/programmed scan
q Select VFO mode with [V/M·S. MW·~].
· Select the desired frequency band with [BAND· ], if desired.
t To start the scan, push [MODE·SCAN].
· Scan pauses when a signal is received. · Rotate [DIAL] to change the scanning direction, or resumes manually. · During full/band scan
FM P SKIP
w Set the squelch to the point where noise is just muted. r Rotate [DIAL] to select the desired scanning type.
· "ALL" for full scan; "BAND" for band scan, "PROGxx" for programmed scan (xx= 0 to 24; programmed scan edges numbers only displayed) · Full scan selection [DIAL]
· During programmed scan
FM P SKIP
6
· Band scan selection [MODE·SCAN]
NOTE: Instead of the steps e to t operations, while pushing and holding [MODE·SCAN], rotate [DIAL] to select the desired scan type. About the scanning steps: The selected tuning step in each frequency band (in VFO mode) is used during scan.
· Programmed scan selection
Selectable between " 0" to "24" if programmed
26
6
SCAN OPERATION
I Scan edges programming
Scan edges can be programmed in the same manner as memory channels. Scan edges are programmed into scan edges, 00A/00B to 24A/24B, in memory channels. w Set the desired frequency: Select the desired band with [BAND· ]. to select select memory write condition.
· 1 short and 1 long beeps sound. ·" " indicator and memory channel number blink.
t Push [V/M·S. MW·~] for 1 sec.
· 3 beeps sound · The other scan edge channel "B, " 00B to 24B, automatically selected when continuing to push [V/M·S. MW·~] after programming.
yTo program a frequency for the other pair of scan edges, 00B or 24B, repeat steps w and r.
· If the same frequency is programmed into a pair of scan edges, programmed scan will not function. [DIAL]
rRotate [DIAL] to select the desired programmed scan edge channel from 00A to 24A.
[V/M·S. MW·~]
[EXAMPLE]: Programming 145. 300 MHz into scan edges 03A.
Push
FM P SKIP
for 1 sec.
FM
Rotate
Push
for 1 sec.
FM P SKIP FM P SKIP
27
SCAN OPERATION
6
I Memory/bank/all bank scan
q Select memory mode with [V/M·S. MW·~].
· Select the desired bank with [BAND· ] for bank scan.
tPush [MODE·SCAN] momentarily to start all bank or bank scan.
· Scan pauses when a signal is received. · Rotate [DIAL] to change the scanning direction, or resumes manually.
w Set the squelch to the point where noise is just muted. to; · When memory mode is selected at the step q: - start memory scan. · When a bank channel is selected at the step q: - enter scan type selection mode. r Rotate [DIAL] to select the desired scanning type.
· "ALL" for all bank scan; "BANK" for bank scan. [DIAL] · All bank scan selection
y To stop the scan, push [MODE·SCAN].
· During memory/all bank scan
W FM AM DUP T SQL DTCS
· During bank scan
W FM AM DUP T SQL DTCS
6
IMPORTANT!: To perform memory or bank scan, 2 or more memory/bank channels MUST be programmed, otherwise the scan never starts.
[MODE·SCAN] · Bank scan selection
28
6
SCAN OPERATION
D During auto-memory write scanning: · When signal is received, scan pauses and the frequency is stored into auto memory write channel group (R000R199).
- 2 short beeps sound when stored.
I Auto memory write scan
This scan is useful for searching a specified frequency range and automatically storing busy frequencies into memory channels. [. . . ] OPC-474 CLONING CABLE For connection between receivers for data cloning.
CS-R5 CLONING SOFTWARE + OPC-478U CLONING CABLE
(USB type)
Allows you to transfer data, such as memories, and quickly and easily edit and store data via a PC (for Microsoft® Windows® 98/Me/2000/XP). Current RS232C (DB 9-pin) type cloning cable, OPC-478, is also available.
65
q Cut w Fold e Complete
POCKET GUIDE
15
Important operating instructions are summed up in this and the following page for your simple reference. By cutting along the line and folding on the dotted line, it will become a card sized operating guide which can easily be carried in a card case or wallet, etc.
iR5
I VFO and memory mode selection Push [V/M·S. MW·~] to toggle between VFO and memory mode. I Receive mode selection Push [MODE·SCAN] several times to select the desired mode I Audio level setting Push [Y] to increase, push [Z] to decrease the audio level. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE ICOM IC-R5
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual ICOM IC-R5 will begin.