User manual INFINITY C336

[. . . ] The CC225 center channel speaker should be placed on top of or directly below the television and aimed toward the listening area. The CC225 speaker may also be wall-mounted. NOTE: An Infinity powered subwoofer will add impact and realism to both music and film soundtracks. Contact your Infinity dealer for recommendations on subwoofer models for your application. Infinity Subwoofer (optional) The Infinity ClassiaTM series of loudspeakers continues the longstanding Infinity® commitment to accurate sound reproduction. [. . . ] NOTE: The customer is responsible for the correct selection and use of mounting hardware (available through hardware stores) that will ensure the proper and safe wall-mounting of the speakers. Attach the wall bracket to the wall at the desired location. Keyhole mounts Step 2. Securely fasten the two cleats to the rear of the speaker, using two included 1/4"-20 panhead screws per cleat. Mark the positions on the wall where you would like to place the mounting screws. Fasten two 1-1/2, " #8 wood screws to the wall using the markings placed in Step 1 as your guide. Place the speaker on the wall by aligning the keyholes on the back of the speaker to the screwheads on the wall. Once positioned properly, the speaker should slide down slightly and become secure. Carefully slide the cleats on the rear of the speakers over the tabs of the wall bracket. INSTALLING SPIKED FEET C336 Four metal spikes are supplied for use when using the outboard feet and the speaker is to be placed on a carpeted surface to decouple the speaker from the floor and prevent unwanted damping. To insert the spikes, gently lay the speaker on its back (not its front or side) on a soft, nonabrasive surface, unscrew the four rubber-tipped feet and store in a safe place. NEVER drag the speaker to move it, as this will damage the spikes, the feet, the wood cabinet itself, and/or the floor. Top view INFINITY CLASSIA 3 WIRING THE SYSTEM IMPORTANT: Make sure all equipment is turned off before making any connections. For speaker connections, use a minimum #16-gauge speaker wire with polarity coding. The side of the wire with a ridge or other coding is usually considered positive polarity (i. e. , +). NOTE: If desired, consult your local Infinity dealer about speaker wire and connection options. The speakers have coded terminals that accept a variety of wire connectors. The most common connection is shown in Figure 5. To ensure proper polarity, connect each + terminal on the back of the amplifier or receiver to the respective + (red) terminal on each speaker, as shown in Figure 6. See the owner's guides that were included with your amplifier, receiver and television to confirm connection procedures. IMPORTANT: Do not reverse polarities (i. e. , + to ­, or ­ to +) when making connections. Doing so will cause poor imaging and diminished bass response. BI-WIRING C336 The outer connection panel and internal dividing network of the C336 is designed so that separate sets of speaker cables can be attached to the lowfrequency transducer and midrange/high-frequency transducer portions of this dividing network. This is called bi-wiring. Bi-wiring can provide several sonic advantages and considerably more flexibility in power amplifier selection. Figure 7. Single-Stereo Amplifier Figure 5. This example shows how to connect bare wires to the terminals. Figure 8. Dual-Stereo Amplifier Figure 9. Figure 6. [. . . ] 2, route de Tours 72500 Château du Loir France declare in own responsibility that the products described in this owner's manual are in compliance with technical standards: EN 61000-6-3:2001 EN 61000-6-1:2001 Laurent Rault Harman Consumer Group, Inc. Château du Loir, France 12/07 6 INFINITY CLASSIA © 2007 Harman International Industries, Incorporated. Infinity Systems, 250 Crossways Park Drive, Woodbury, NY 11797 USA 516. 674. 4463 (USA only) www. infinitysystems. com Infinity and CMMD (patent nos. [. . . ]