User manual INFINITY REFERENCE 4012I 5012I 6012I 6012SI 9612I 9613I 3012CF 6412CF 6412CFP 6812CF

[. . . ] 4012i , 5012i , 6012i , 6012si , 9612i , 9613i , 3012cf , 6412cf , 6412cfp , 6812cf instructi o reference series ns THANK YOU for purchasing Infinity's Reference Series multielement automotive loudspeakers. We've organized this manual to make their installation as simple and trouble-free as possible. Remember to keep your sales receipt with this manual in a safe place so both are available for future reference. [. . . ] When moving a speaker, always rest it with the cone or dome facing up. · Check clearances on both sides of a planned mounting surface before drilling any holes or installing any screws. · At the installation sites, locate and make a note of all fuel lines, hydraulic brake lines, vacuum lines and electrical wiring. Use extreme caution when cutting or drilling in and around these areas. CAUTION: In some cars, fuel tanks may be located directly beneath the rear deck. Check for adequate speaker basket clearance before considering this location!· Before drilling or cutting holes, use a utility knife to remove unwanted fabric or vinyl, to keep material from snagging in a drill bit or saw. · For door installations, check the clearance with the windows throughout the range of the window's travel, and verify that a mounted speaker will not interfere with the window crank or power window mechanism. · If mounting speakers elsewhere, check for clearance around rear deck torsion bars, glove box or other structural elements. · Do not mount speakers where they will get wet. INSTALLATION Figure 1. Note:The 3012cf, 6412cf, 6412cfp and 6812cf speakers are designed to be installed under factory grilles. Modifying the 4012i to be installed in locations requiring fewer than 4 mounting "ears" . Note: Bend tab back and forth to detach it from the speaker. Note:The 6812cf is intended to replace 5" x 7" and 6" x 8" speakers. INSTALLATION Figure 3. Note:The 6412cf and 6412cfp are designed to be installed under factory grilles. [. . . ] The metal ring can be mounted in many European vehicles, while the plastic ring can be mounted in many vehicles using 6-3/4" speaker locations or three-point mounting frames. FOAM GASKET FOAM GASKET MOUNTING RING reference series SPECIFICATIONS 4012i Type: Speaker Impedance: Power Handling: Frequency Response: Sensitivity (2. 83V, 1m): Mounting Depth: Cutout Diameter: 5012i Type: Speaker Impedance: Power Handling: Frequency Response: Sensitivity (2. 83V, 1m): Mounting Depth: Cutout Diameter: 6012i Type: Speaker Impedance: Power Handling: Frequency Response: Sensitivity (2. 83V, 1m): Mounting Depth: Cutout Diameter: 4" 2-Way 4 Ohms 35W RMS, 105W Peak 85Hz ­ 21kHz 91dB 1-7/8" (48mm) 3-3/4" (96mm) 6012si Type: Speaker Impedance: Power Handling: Frequency Response: Sensitivity (2. 83V, 1m): Mounting Depth: Cutout Diameter: 9612i Type: Speaker Impedance: Power Handling: Frequency Response: Sensitivity (2. 83V, 1m): Mounting Depth: Cutout Diameter: 6-1/2" Shallow-Mount 2-Way 4 Ohms 50W RMS, 150W Peak 53Hz ­ 21kHz 92dB 1-15/16" (50mm) 5" (127mm) 3012cf Type: Speaker Impedance: Power Handling: Frequency Response: Sensitivity (2. 83V, 1m): Mounting Depth: Cutout Diameter: 6412cf Type: Speaker Impedance: Power Handling: Frequency Response: Sensitivity (2. 83V, 1m): Mounting Depth: Cutout Diameter: 3-1/2" 2-Way 4 Ohms 25W RMS, 75W Peak 85Hz ­ 21kHz 90dB 1-7/16" (37mm) 3-1/16" (78mm) 6812cf Type: Speaker Impedance: Power Handling: Frequency Response: Sensitivity (2. 83V, 1m): Mounting Depth: Cutout Diameter: 6" x 8"/5" x 7" 2-Way 4 Ohms 60W RMS, 180W Peak 49Hz ­ 21kHz 92dB 2-7/16" (62mm) 5" x 7-3/16" (127mm x 183mm) 5-1/4" 2-Way 4 Ohms 45W RMS, 135W Peak 67Hz ­ 21kHz 91dB 2-1/4" (58mm) 4-11/16" (120mm) 6" x 9" 2-Way 4 Ohms 100W RMS, 300W Peak 46Hz ­ 21kHz 92dB 3" (77mm) 6-1/16" x 8-7/8" (154mm x 226mm) 4" x 6" 2-Way 4 Ohms 40W RMS, 120W Peak 72Hz ­ 21kHz 91dB 1-15/16" (50mm) 3-5/8" x 5-5/8" (93mm x 143mm) 6-1/2" 2-Way 4 Ohms 60W RMS, 180W Peak 53Hz ­ 21kHz 92dB 2-1/16" (53mm) 5" (127mm) 9613i Type: Speaker Impedance: Power Handling: Frequency Response: Sensitivity (2. 83V, 1m): Mounting Depth: Cutout Diameter: 6" x 9" 3-Way 4 Ohms 100W RMS, 300W Peak 46Hz ­ 21kHz 92dB 3" (77mm) 6-1/16" x 8-7/8" (154mm x 226mm) 6412cfp Type: Speaker Impedance: Power Handling: Frequency Response: Sensitivity (2. 83V, 1m): Mounting Depth: Cutout Diameter: 4" x 6" 2-Way Plate 4 Ohms 45W RMS, 135W Peak 72Hz ­ 21kHz 91dB 1-15/16" (50mm) 3-9/16" x 5-11/16" (91mm x 145mm) Declaration of Conformity A valid serial number is required for warranty coverage. Features, specifications and appearance are subject to change without notice. We, Harman Consumer Group International 2, route de Tours 72500 Chateau-du-Loir France declare in own responsibility that the products described in this owner's manual are in compliance with technical standards: EN 61000-6-3:2001 EN 61000-6-1:2001 Infinity Systems, 250 Crossways Park Drive, Woodbury, NY 11797 USA 516. 674. 4463 · FAX 516. 682. 3523 · www. infinitysystems. com © 2005 Harman International Industries, Incorporated · Part No. REFME1/05 ¤ Klaus Lebherz Harman Consumer Group International Chateau-du-Loir, France 1/05 [. . . ]