User manual INFINITY REFERENCE 5010CS 6010CS 6810CS

[. . . ] 5010cs , 6010cs , 6810cs instructi o reference series ns INSTALLATION WARNINGS AND TIPS THANK YOU for purchasing Infinity's Reference Series automotive loudspeaker components. We've organized this manual to make your installation as simple and trouble-free as possible. Remember to keep your sales receipt with this manual in a safe place so both are available for future reference. [. . . ] · At the installation sites, locate and make a note of all fuel lines, hydraulic brake lines, vacuum lines, and electrical wiring. Use extreme caution when cutting or drilling in and around these areas. CAUTION: In some cars, fuel tanks may be located directly beneath the rear deck. Check for adequate speaker basket clearance before considering this location!· Before drilling or cutting holes, use a utility knife to remove unwanted fabric or vinyl, to keep material from snagging in a drill bit or saw. · For door installations, check the clearance with the windows throughout the range of the window's travel, and verify that a mounted speaker will not interfere with the window crank or power window mechanism. · If mounting speakers elsewhere, check for clearance around rear deck torsion bars, glove box, or other structural elements. · Do not mount speakers where they will get wet. INSTALLATION Figure 1. Mounting the 6010cs in 165mm speaker locations. FOAM GASKET Figure 2. Mounting the 6010cs woofer with the grille. MOUNTING RING INTERMOUNT III (PATENT NO. 6, 505, 705) The 6010cs is packaged with two different speaker adaptor rings. These are used to install the 6-1/2" speakers in various vehicles. The metal ring can be mounted in many European vehicles, while the plastic ring can be mounted in many vehicles using 6-3/4" speaker locations or three-point mounting frames. Mounting the 6010cs woofer in standard speaker locations. Note: The 6810cs is designed to replace 5" x 7" and 6" x 8" speakers installed behind existing vehicle grilles, and does not include grilles. FOAM GASKET INSTALLATION FLUSH-MOUNT Figure 5A. 5, 859, 917) flush-mounting kit. 3 TWEETER ANGLE Figure 6. 3 ROTATE ENTIRE ASSEMBLY TO AIM ANGLED TWEETER TOWARD LISTENER. Figure 7A. Mounted to grille panel. 1 SLIDE SCREW UP OR DOWN TO ADJUST TWEETER ANGLE. 1 2 Note: Aim the tweeter at the listening position by sliding the stud in the groove on the back of the tweeter cup and rotating the entire assembly in the mounting surface. [. . . ] Figure 8B. 6010cs Type: Speaker Impedance: Power Handling: Frequency Response: Sensitivity (2. 83V, 1m): Crossover Frequency: Mounting Depth: Cut-out Diameter: 6-1/2" 2-Way Component System 4 Ohms 90W RMS, 270W Peak 53Hz ­ 21kHz 92dB 3. 5kHz Woofer: 2-1/16" (53mm) Tweeter: 5/8" (16mm) Woofer: 5" (127mm) Tweeter: 1-3/4" (45mm) A valid serial number is required for warranty coverage. Features, specifications and appearance are subject to change without notice. Declaration of Conformity We, Harman Consumer Group International 2, route de Tours 72500 Chateau-du-Loir France declare in own responsibility that the products described in this owner's manual are in compliance with technical standards: EN 61000-6-3:2001 EN 61000-6-1:2001 BIG LUG IS POSITIVE (+) SMALL LUG IS NEGATIVE (­) Infinity Systems · 250 Crossways Park Drive, Woodbury, NY 11797 USA 516. 674. 4463 · FAX 516. 682. 3523 · www. infinitysystems. com © 2005 Harman International Industries, Incorporated · Part No. REFCSOM1/05 ¤ Klaus Lebherz Harman Consumer Group International Chateau-du-Loir, France 1/05 [. . . ]