User manual MAXTOR TM1300
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual MAXTOR TM1300. We hope that this MAXTOR TM1300 user guide will be useful to you.
Manual abstract: user guide MAXTOR TM1300
Detailed instructions for use are in the User's Guide.
[. . . ] Application Note:
PULNiX TM-1300
Camera Descriptions
· · · · · ·
Interfacing non-standard cameras to Matrox Pulsar March 30, 1998
1284 x 1029 x 10-bit. [. . . ] Refer to the camera manual for more information.
Cabling Requirements
Mode 1: Continuous mode · PULSAR/DIG/MOD required for digital data and syncs in RS-422 format.
·
The connections between the 68-pin connector of the PULSAR/DIG/MOD and the 31-pin connector of the camera are as follows:
PULSAR/DIG/MOD (68-pin connector) Pin name Pin no. CLKIN+ 29 CLKIN- 63 HSYNC+ 26 HSYNC- 60 VSYNC+ 25 VSYNC- 59 GROUND 34 GROUND 12 DATA0+ 20 DATA0- 54 DATA1+ 19 DATA1- 53 DATA2+ 16 DATA2- 50 DATA3+ 15 DATA3- 49 DATA4+ 14 DATA4- 48 DATA5+ 13 DATA5- 47 DATA6+ 11 DATA6- 45 DATA7+ 10 DATA7- 44 DATA8+ 09 DATA8- 43 DATA9+ 08 DATA9- 42 PULNiX TM-1300 (31-pin DC connector) Pin name Pin no. CLK+ 01 CLK- 17 LDV+ 02 LDV- 18 FDV+ 03 FDV- 19 GND 04 GND 16 D0+ 06 D0- 22 D1+ 07 D1- 23 D2+ 08 D2- 24 D3+ 09 D3- 25 D4+ 10 D4- 26 D5+ 11 D5- 27 D6+ 12 D6- 28 D7+ 13 D7- 29 D8+ 14 D8- 30 D9+ 15 D9- 31
PUL-CID-051
2
Application Note:
PULNiX TM-1300
Interfacing non-standard cameras to Matrox Pulsar
March 30, 1998
Cabling Requirements
Mode 2: Asynchronous Reset mode
·
IMG-7W2-TO-5BNC cable required for TTL external trigger; PULSAR/DIG/MOD required for digital data and syncs in RS-422 format, and for TTL control signal. The connections between the 68-pin connector of the PULSAR/DIG/MOD and the 31-pin connector of the camera are as in continuous mode (digital video output) plus the following extra connections:
PULSAR/DIG/MOD (68-pin connector) Pin name TTL_EXPOSURE1 PULNiX TM-1300 (31-pin DC connector) Pin name Pin no. 66
·
TTL external trigger source should be connected to the TTL Trigger Input of the IMG-7W2TO-5BNC cable. An RS-422 external trigger input may also be used once the following connections between the 68-pin connector of the PULSAR/DIG/MOD and the external trigger source are made:
PULSAR/DIG/MOD (68-pin connector) Pin name TRIGGER+ TRIGGERExternal trigger source Pin no. 27 61 Pin name "RS-422 TRIGGER+" "RS-422 TRIGGER-"
·
·
Use Matrox Intellicam in order to modify the DCF for an RS-422 external trigger input. Consult the Matrox Intellicam User Guide for more information
The DCF(s) mentioned in this application note can be found on the MIL and MIL-Lite CD, or our FTP site (ftp. matrox. com). [. . . ] 1901, 19/F, Workington Tower, 78 Bonham Strand E. , Sheung Wan, Hong Kong. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE MAXTOR TM1300
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual MAXTOR TM1300 will begin.