User manual MIELE KM 532

[. . . ] Operating and Installation instructions Ceramic hobs KM 530 / KM 537 KM 540 / KM 541 / KM 542 / KM 543 KM 544 / KM 545 / KM 547 / KM 548 KM 550 / KM 551 / KM 552 / KM 553 To avoid the risk of accidents or damage to the appliance it is essential to read these instructions before it is installed and used for the first time. GHirZ M. -Nr. 68 3 Guide to the appliance KM 540 Cooking zones: abcd Single circle zones Sensor switches for: e Cooking zones f Timer (see "Timer sensors and display") g Safety lock h Hob ON/OFF Indicator lamp for: i Safety lock 4 Guide to the appliance KM 544 Cooking zones: abcd Single circle zones Sensor switches for: e Cooking zones f Timer (see "Timer sensors and display") g Safety lock h Hob ON/OFF Indicator lamp for: i Safety lock 5 Guide to the appliance KM 530 / KM 545 Cooking zones: abd Single circle zones c Double circle zone Indicator lamps for: i Safety lock k Outer circle of the double circle zone Sensor switches for: e Cooking zones f Timer (see "Timer sensors and display") g Safety lock h Hob ON/OFF j Switching on the outer circle of the double circle zone 6 Guide to the appliance KM 541 Cooking zones: a Double circle zone Indicator lamps for: i Safety lock k Outer circle of the double circle zone bcd Single circle zones Sensor switches for: e Cooking zones f Timer (see "Timer sensors and display") g Safety lock h Hob ON/OFF j Switching on the outer circle of the double circle zone 7 Guide to the appliance KM 542 Cooking zones: ac Double circle zones bd Single circle zones Sensor switches for: e Cooking zones f Timer (see "Timer sensors and display") g Safety lock h Hob ON/OFF j Switching on the outer circle of the double circle zone Indicator lamps for: i Safety lock k Outer circle of the double circle zone 8 Guide to the appliance KM 548 Cooking zones: ac Double circle zones bd Single circle zones Sensor switches for: e Cooking zones f Timer (see "Timer sensors and display") g Safety lock h Hob ON/OFF j Switching on the outer circle of the double circle zone Indicator lamps for: i Safety lock k Outer circle of the double circle zone 9 Guide to the appliance KM 543 / KM 547 Cooking zones: a Double circle zone Indicator lamps for: i Safety lock k Outer circle of the double circle / extended cooking zone bd Single circle zones c Extended cooking zone Sensor switches for: e Cooking zones f Timer (see "Timer sensors and display") g Safety lock h Hob ON/OFF j Switching on the outer circle of the double circle / extended cooking zone 10 Guide to the appliance KM 537 / KM 550 / KM 551 KM 552 / KM 553 Cooking zones: a Double circle zone Indicator lamps for: i Safety lock k Outer circle of the double circle / extended zone bd Single circle zones c Extended cooking zone Sensor switches for: e Cooking zones f Timer (see "Timer sensors and display") g Safety lock h Hob ON/OFF j Switching on the outer circle of the double circle / extended cooking zone 11 Guide to the appliance Cooking zone sensors and displays l Displays: 0 = 1 to 9 = # = F = A = P0 etc. = Cooking zone ready for use Power setting Residual heat Fault (see "Safety switch-off") Auto heat-up when the power setting range has been extended Programme (see "Programming") Status (see "Programming") m Indicator lamp for Auto heat-up or extended power setting (see "Programming"), e. g. the front left cooking zone n Power setting sensor switches Timer sensors and display o Sensor switches for setting the timer, switching between timer functions and selecting automatic switch-off for a cooking zone. [. . . ] To activate Stop and Go: ^ Touch the $ sensor until you hear two consecutive beeps. Be careful not to continue touching the $ sensor for too long, as this will activate the safety lock. The power of the cooking zone in use will be reduced to setting 1, and a 1 will appear in the corresponding cooking zone display. If automatic switch-off is programmed for a cooking zone, activating Stop and Go will interrupt the count down to the switch-off time. When Stop and Go is deactivated, the automatic switch-off programme time will continue to run without further interruption. If a minute minder time has been set, this will continue running and will not be affected by Stop and Go. To deactivate Stop and Go: ^ Touch the safety lock sensor $ until the indicator lamp goes out. The cooking zones will now run at the level that was previously set. 31 Safety features Safety switch-off Safety switch-off with an over-long cooking time Your hob is fitted with a safety switch-off feature in case you forget to switch it off yourself. If one of the cooking zones is heated for an unusually long period of time (see chart), and the power settings are not altered, the hob will switch itself off automatically and the appropriate residual heat indicator will appear. Power setting* Maximum operating time in hours 10 5 5 4 3 2 2 2 1 Safety switch-off if the sensors are covered Your hob will switch off automatically if one or several of the sensors remain covered for longer than 10 seconds, for example, by finger contact, food boiling over or by an object such as an oven glove or tea towel. An audible tone will sound every 30 seconds (for a maximum of ten minutes) and an F will flash in the display for the sensor which is covered. 1 / 1. The cooking zones can now be used again as normal. * The power settings with a dot after the number are only available if the power setting range has been extended (see "Programming - P6. "). ^ To use the cooking zones again, switch the hob back on in the usual way. 32 Safety features Overheating protection Each cooking zone is equipped with overheating protection. An internal temperature limiter switches off the heating elements in the cooking zone before the ceramic surface overheats. Once the ceramic has cooled down to a safe level the heating will automatically switch back on again. Overheating can be caused by: ­ switching on a cooking zone without a pan on it. You can tell that the overheating protection has activated because the heating switches on and off even when the highest setting is selected. 33 Timer This hob is equipped with a timer which can be used as a minute minder or to automatically switch off a zone of your choice. Both functions can be operated at the same time. Programming steps in brief Switching on Setting the timer Touch m from 99 to 00 minutes use the - sensor switch from 00 to 99 minutes use the + sensor switch Touch m Touch - and + at the same time Switching between timer functions Re-setting the timer to 00 Setting the minute minder The minute minder can be used with the hob switched on or off. ^ Touch - or + until the time you require appears in the display, e. g. 15 minutes. When the set time has elapsed 00 will appear in the display. To turn the buzzer off before this, touch the m sensor. The time then counts down in minutes. The time remaining can be seen in the display and changed at any time by touching - or +. 34 Timer Switching a cooking zone off automatically It is only possible to switch a cooking zone off automatically if a power setting has already been selected for that zone. [. . . ] This could cause difficulties if the hob ever needs to be taken out for servicing and possibly result in damage to the frame or the worktop. 61 Installation Flush-fitted hobs Building-in dimensions for KM 552 N. B. Cut-out dimensions 470-1 and 730-1 are for the step required in granite and marble worktops only It is essential to follow the detailed drawings on the next pages too. 62 Installation The hob can be installed b Building-in depth c Building-in depth for mains connection box d Front ­ directly into a suitable cut-out in a granite or marble worktop. ­ in a suitable cut-out in a tiled or solid wood worktop with a wooden support frame. The frame must be provided on site, and is not supplied with the appliance. Flush fit hobs are only suitable for installation in granite, marble, tiled or solid wood worktops. [. . . ]