User manual NAIM ARO

[. . . ] 9 UnitiQute Specifications 21 7 7. 1 7. 2 7. 3 8 8. 1 8. 2 8. 3 UnitiQute UPnPTM Audio Interface UPnPTM Servers Audio File Compatibility Scanning Servers and Playing Files UnitiQute USB/iPod Interface USB Media and File Compatibility iPod Compatibility and Charging Browsing and Playing USB Files 19 19 19 19 20 20 20 20 6. 1 6. 2 6. 3 6. 4 6. 5 6. 6 UnitiQute Multi-mode Radio Tuner FM Tuner ­ Seeking Stations DAB Tuner ­ Seeking Stations iRadio Tuner ­ Seeking Stations Adding iRadio Stations Storing Radio Presets Using Radio Presets 17 17 17 17 18 18 18 Page 5 5. 1 5. 2 5. 3 5. 4 5. 5 UnitiQute Integrated Amplifier Selecting Inputs Volume Control Amplifier Display Signal Outputs Amplifier Fault Warnings 16 16 16 16 16 16 "Made for iPod" and "Made for iPhone" mean that an electronic accessory has been designed to connect specifically to iPod or iPhone respectively and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. UPnPTM is a trademark of the UPnPTM Forum. Un itiQ u t e Intro du c tio n 1 U n it iQ u t e Introd ucti o n UnitiQute is a highly capable product that will repay time and effort spent on installation and setup. Each of these is introduced in the following paragraphs and subsequently described in full detail in Sections 5 to 8. [. . . ] iPod battery charging takes place always when the iPod is connected or never takes place. Enabled: Yes Name: USB/iPod Input Trim: 0 4Folder History: No Options Large / Small / None Yes / No 0 to 100 (adjust using handset 6or 5 keys) -10 to + 10 (adjust using handset 6or 5 keys) The speaker type options specify high-pass filtering settings. Select the Large option when the UnitiQute preamplifier output is connected to an external power amplifier or to a subwoofer used to augment the low frequency performance of large (full bandwidth) speakers. Select Small only when the UnitiQute preamplifier output is connected to a subwoofer used to provide the low 11 Note: The non-charging option is provided because there is a small reduction in iPod sound quality when simultaneously charging and playing. This means however that an iPod can potentially run out of power while playing via the UnitiQute. Un itiQ u t e Setu p frequency component of a speaker system incorporating small (restricted bandwidth) satellite speakers. When Small is specified, a 100Hz high-pass filter is applied to the UnitiQute speaker output signal. Select None when no speakers are connected directly to the UnitiQute Engaging the Loudness option applies low frequency boost to the speaker and preamplifier outputs that decreases as the volume setting is increased. Through compensating for the ear's reduced low frequency sensitivity at low volume levels, the Loudness function can make low volume listening more satisfying. Note: The loudness contour operates at volume settings between 0 and 55. Volume and Balance parameters specify maximum allowed volume, and the channel balance respectively. Note: Devices installed on a network have an IP address through which they are identified by all the other items on the network. DHCP is a set of rules that enable the automatic allocation of addresses as items are connected (or switched on while connected) to the network. The UnitiQute MAC address is shown in the `Factory settings > System Status' page. Note: The wireless passphrase/access key is created when the wireless router is first set up and could be a word or a series of numbers and letters. If the passphrase/access key is not known, check on the router settings page or with the person who initially set up the router. Note: If a router offers multiple security configurations, UnitiQute will automatically offer only the most secure one. Note: If WEP security is used the router should be set to "auto" or "open" authentication. If the selected network is insecure and requires no passphrase or access key to join, UnitiQute will display an alert message. Pressing the handset ok/list key will immediately connect UnitiQute to the network and display a confirmation screen. This wireless network is insecure and requires no passphrase or access key. Press OK To Connect 4. 7 The Digital Output Menu The Digital Output setup menu enables the UnitiQute digital output to be switched on and its signal format configured. Parameter Enabled: Output: Digital Output 4Enabled: Output: 1/2 No Native Options Yes / No Native / 96kHz 24bit If Native is selected, the digital output format will reflect the input format. If 96kHz 24bit is selected, the output is re-sampled to 96kHz and 24bit resolution. 4. 8 The Front Display Menu The Front Display setup menu Front Display 1/5 enables the behaviour of 4Off During Mute: No the front panel display, logo Auto Off: 2 mins illumination, clock display Clock When Off: Yes Logo Off: If Muted and logo touch-muting to be modified. The options are tabulated and described in the following section: Parameter Off During Mute: Auto Off: Clock When Off: Logo Off: Logo Mute: Options Yes / No Select time from list Yes / No If Muted / If Display Off / Always / Never Yes / No Note: Wireless connection difficulties can sometimes be resolved by changing the wireless connection channel in the router settings. 4. 6. 2 Non-DHCP (Static) Network Connection If DHCP is de-selected in the Network Settings menu, five further parameters will be displayed. [. . . ] Tracks can then be selected for playback by using the up (5), down (6) and ok/list keys. In long lists the handset numeric/text keys can be used to jump through the list alphabetically. Once playback is underway the UnitiQute display will exit from list mode and revert to normal mode where the handset transport keys ( ) can be used to control playback. To re-enter list mode for further list browsing and selecting press the handset ok/list key. [. . . ]