User manual NEC IDC-3000
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual NEC IDC-3000. We hope that this NEC IDC-3000 user guide will be useful to you.
Manual abstract: user guide NEC IDC-3000
Detailed instructions for use are in the User's Guide.
[. . . ] NEC Improved Definition Converter IDC-3000
NEC Improved Definition Converter IDC-3000
User's Manual
R
NEC Technologies, Inc. 1255 Michael Drive Wood Dale, Illinois 60191
Printed in Japan 79TM0282
WARNING
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO DO NOT USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS, UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. [. . . ] High impedance input
7 RGB Input Connector (THROUGH)
RGB (D-sub 15 miniature) . . . . See page A for pin assignment.
4 BNC/S-VIDEO Switch (VIDEO 1 and VIDEO 2)
BNC . . . . . . . . . . . . . . . . Provides the appropriate switching when the signal is input from the BNC input jacks. Provides the appropriate switching when the signal is input from the S-VIDEO input jack.
9
0
8 MONITOR Output Jack (OUTPUT)
MONITOR (BNC) . . . . . . . . . . . Outputs an S video signal, (derived from the signal of the equipment connected to VIDEO 1 or VIDEO 2), which has been divided to a luminance signal (Y) and a chrominance signal (C). Outputs the signal of the equipment connected to VIDEO input 1 through 5 and the AUDIO L and R associated with the RGB input connector. The selected video signal is output when RGB input has been selected and MONITOR button is switched on. Connected to the H/V input jack of a monitor or projector having a 31. 5 kHz horizontal scanning function. Switch
Selects the polarity of the horizontal and vertical output signals. Active low
A PC-CONTROL SW (Switch)
Selects the communications standard of the PC-CONTROL connector. RS-232C standard
9 RGB Output Connector (OUTPUT)
RGB (BNC) . . . . . . . . . . . . . . . . . . . . . . Connected to the RGB input jacks of a monitor or projector having a 31. 5 kHz horizontal scanning function. Connected to the HORIZONTAL input jack of a monitor or projector having a 31. 5 kHz horizontal scanning function. Connected to the VERTICAL input jack of a monitor or projector having a 31. 5 kHz horizontal scanning function.
B AC IN Receptacle
Used to connect the supplied power cord.
C PC-CONTROL Connector (15-pin connector)
Connect to a personal computer or other control equipment.
D EXTERNAL CONTROL Connector
Connections are made to this connector when controlling this unit by external control. (See the "External Control Mode" section. )
RGB (D-Sub 15 mini) Connector Pin Assignment
Pin No.
6
5
4 10 9
3 8
2 7
1
Signal to be connected Red input Green input Blue input GND GND Red GND Green GND Blue GND Open Sync GND GND Open H-Sync V-Sync Open
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
15 14 13 12 11
NOTE : · Use a signal conforming to the standard TV signal when connecting an input source. · Using poor quality video tape may cause distortion on the picture.
A
B
REMOTE CONTROL
1 POWER Button
Turns the power on or off.
2 VIDEO 1 Button
Switches the unit to the video 1 input mode.
1 3 2 7 9 C E
POWER
4 5
MONITOR
3 VIDEO 2 Button
Switches the unit to the video 2 input mode.
VIDEO1 VIDEO2 VIDEO3 VIDEO4 VIDEO5 RGB
6 0 8 B F
4 VIDEO 3 Button
Switches the unit to the video 3 input mode.
SPLIT
NOISE REDUCTION
5 VIDEO 4 Button
Switches the unit to the video 4 input mode.
MOVIE
STILL
D
A
NORMALIZE MODE1 MODE2 UP DOWN
6 VIDEO 5 Button
Switches the unit to the video 5 input mode.
7 RGB Button
Switches the unit to the RGB input mode.
REMOTE CONTROL UNIT RD-338E
8 MONITOR Button
Used to switch on the monitor mode at the time of RGB input.
9 SPLIT
Press to activate the demonstration split mode function for processing the artificial interlace and switching off the 3-dimensional Y/C separation processing the right half of the screen. This function is for use when the NTSC indicator is lit.
0 NOISE REDUCTION Button
Used when screen noise becomes annoying. Each time this button is pressed, the NR function will change as follows:
OFF NOISE REDUCTION 1 NOISE REDUCTION 2
(Noise is reduced) (Noise is further reduced)
E MODE 2 Button
Used to select the image system. Each time this button is pressed, mode 2 will change as follows:
SPLIT MOVIE
· SPLIT . . . . . . . . . . Selects the demonstration split mode function for processing the artificial interlace and switching off the 3dimensional Y/C separation processing the right half of the screen. Mode Normal Movie 1 Movie 2 Movie 3 Y/C Separation Motion adaptation Move mode Move mode Motion adaptation Image Interpolation Motion adaptation Move mode Motion adaptation Move mode
A MOVIE Button
Press to manually set the method of Y/C separation and image interpolation.
B STILL Button
Press to display still images such as those from document cameras, etc. The Y/C separation and image interpolation will be set for the still screen mode.
C NORMALIZE Button
Sets the various adjustments to the standard settings (which had been set at the factory prior to shipping).
D MODE 1 Button
Selects image adjustment and audio adjustment. [. . . ] (hereafter NECTECH) warrants this product to be free from defects in material and workmanship under the following terms. HOW LONG IS THE WARRANTY Parts and labor are warranted for (1) One Year from the date of the first customer purchase. WHO IS PROTECTED This warranty may be enforced only by the first purchaser. WHAT IS COVERED AND WHAT IS NOT COVERED Except a specified below, this warranty covers all defects in material or workmanship in this product. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE NEC IDC-3000
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual NEC IDC-3000 will begin.