User manual OKI LD610
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual OKI LD610. We hope that this OKI LD610 user guide will be useful to you.
Manual abstract: user guide OKI LD610
Detailed instructions for use are in the User's Guide.
[. . . ] LD610
User's Technical Reference
59103001
© 2011 OKI Data Americas, Inc.
Safety Precautions
Safety Precautions
Please read the following information carefully before installing and using the printer. Pictographic Symbols This instruction manual and the printer labels use a variety of pictographic symbols to facilitate safe and correct use of the printer and to prevent injury to others and property damage. Be sure to understand these symbols well before reading the main text.
Ignoring the instructions marked by this symbol and erroneously operating the printer could result in death or serious injury. Ignoring the instructions marked by this symbol and erroneously operating the printer could result in injury or property damage.
Example Pictographs
The pictograph means "Caution is required. " A specific warning symbol is contained inside this pictograph (The symbol at left is for electric shock). [. . . ] To be connected by Port1024 and Port1025 (2 port connections) or Port 9100 (1 port connection)
Page 3-16
LD610 User's Technical Reference
Section 3: Operation and Configuration
3. 9 HEX DUMP MODE
HEX Dump Mode allows you to print the contents of the receive buffer in a hexadecimal format. This feature allows the data stream to be examined for errors and troubleshooting. After selecting the HEX Dump Mode in Operation Setting Mode, restart the printer (refer to Section 3. 5 Operation Setting Mode). The printer then awaits data feeds and when data arrives, it prints out the HEX data continuously. To exit the HEX Dump Mode, restart the printer by turning off the printer and then on again.
3. 10 ERROR OCCURRENCE WHILE DOWNLOADING
The following are the possible causes of errors in program/font download. (1) The flash ROM may be in a state that fails to permit data being written to it. (2) Incorrect data are received while transferring downloaded data.
3. 10. 1 Operation Status when having an Error in Downloading Process
The ERROR indicator and buzzer response when having an error in downloading process are as follows. Operation status Flash ROM error Download data error ON LINE (POWER) indicator Off Off ERROR indicator Red light Long blink interval Buzzer 1 long beep sound 1 long beep sound
Caution
· · · DO NOT turn the printer OFF when data is transferring to the flash ROM in Program or Boot Download mode, as it may corrupt the firmware and prevent the printer from starting up correctly. Ensure to check the printer status when downloading, and do not turn off the printer during download. Ensure that the printer is running on a stable power supply during flash ROM writing operations.
LD610 User's Technical Reference
Page 3-17
Section 3: Operation and Configuration
3. 11 PRINTER CONFIGURATIONS SETTING
You can set the printer configuration by sending SBPL commands from the host computer or by using the Utilities Tool application provided (OKI Accessory CD-ROM). 1 2 3 4 5 6 7 8 9 10 11 12 13 13 14 15 16 17 18 19 20 21 22 23 24 25 26 RS-232C interface *1 Offset setting Base reference point Media size Category Operation mode Setting item Print method (LD610 T printer only) Print speed Print mode Cutter mode Dispenser mode Nonesepa mode Print darkness Print darkness level Sensor type Zero slash Kanji code Initial feed Character pitch Option Waiting time Pitch Width Vertical print position offset Horizontal print position offset Continuous mode Tear Off mode Cutter mode Dispenser mode Baud rate Data bit Parity Stop bit Control Setting contents Thermal Transfer/ Direct Thermal 50mm/s to 100mm/s Continuous/ Tear Off/ Cutter/ Dispenser/ Nonesepa (Linerless) Head position/ Cut position/ No backfeed Head position/ Dispense position Tear Off position/ No backfeed A 1 to 5 I-Mark/Gap/Sensor-off/Transmissive (CX compatible) Disabled/ Enabled JIS code/SJIS code Disabled/ Enabled Fixed/ Proportional 5 to 200 (x100ms) 1 to 2400 dots (including liner/backing paper) [LD610 T/D] 1 to 832 dots (including liner/backing paper) [LD610 T/D] ±792dot ±792dot ±99dot ±99dot ±99dot ±99dot 9600/19200/38400bps 7/8 bit No parity/Odd number/Even number 1/2 bit READY/BUSY control (single item buffer), READY/BUSY control (multi buffer), Xon/Xoff, Protocol for driver(STATUS4), STATUS3
Page 3-18
LD610 User's Technical Reference
Section 3: Operation and Configuration
No. 27
Category LAN interface *2
Setting item LAN mode
Setting contents Protocol for driver(STATUS4)Cyclic response *3 Protocol for driver(STATUS4)ENQ response *3 1 port connection/ENQ response(STATUS3) Multi/ 1 item 010 to 200 (1=50ns) Standard code/Nonstandard code Nonstandard code settings for STX, ETX, ESC, ENQ, CAN, NULL, OFFLINE Download firmware from the host computer. (1) Start up in program download mode (Available in normal operation mode only) (2) Start up in normal operation mode (Available in program download mode only)
28 28 29 30 31
IEEE 1284 interface *4 Non-standard code
Buffer type ACK width Nonstandard code switching Nonstandard code setting
Download
Firmware download Reboot mode *5
*1. Use OKI port or Port 9100 when sending print request from the printer driver. The printer will restart in specified mode.
LD610 User's Technical Reference
Page 3-19
Section 3: Operation and Configuration
This page is intentionally left blank
Page 3-20
LD610 User's Technical Reference
Section 4: Troubleshooting
TROUBLESHOOTING
If you are unable to produce printouts on the LD610 Series printer, use this section to make sure the basics have been checked, before deciding you are unable to proceed any further. This section is divided into four parts: · · · · 4. 1 Error signal troubleshooting 4. 2 Troubleshooting table 4. 3 Interface troubleshooting 4. 4 Test print troubleshooting
LD610 User's Technical Reference
Page 4-1
Section 4: Troubleshooting
4. 1 ERROR SIGNAL TROUBLESHOOTING
The ON LINE (POWER) and ERROR indicators light or flash in different colors and patterns listed below to alert user that an error has occurred on the printer. [Indicator sequence (as shown from left to right): Off, Red light, Green light] ON LINE (POWER) LED
Contents
ERROR LED
Buzzer
Causes
Corrective Actions
Hardware error
FLASH ROM error Off Solid red 1 long beep sound 1) FLASH ROM read/ write error. 1), 2) Board replacement.
Setting information (FROM) error
Machine error
Program error
Incorrect program error
Off Solid red -- 1) Download did not complete successfully. 1) Download again.
Communication error
Communication error by kit Buffer over Off [Red->Off] x twice ->Red x twice>Off (blinks with changing interval) 1 long beep sound Error contents may vary depending on the kit installed. 2) Set the correct protocol.
Download error
Download error
Off Red x 4 times >Off (longest blink interval) 1 long beep sound 1) Downloaded wrong data. 1) Download again.
Page 4-2
LD610 User's Technical Reference
Section 4: Troubleshooting
4. 1 ERROR SIGNAL TROUBLESHOOTING (Cont'd)
Contents
ON LINE (POWER) LED
ERROR LED
Buzzer
Causes
Corrective Actions
Minor error
Cover open Off Blinking red 3 short beeps sound 1) Cover is not closed properly. 2) Sensor type adjustment.
Option
Cutter error Off long blink interval 3 short beeps sound 1) Cutter is not connected. [. . . ] This operational mode is specifically applicable to print operations where the label is to be immediately adhered. LINERLESS (Non Sepa) MODE When the linerless option is installed and enabled, this mode of operation allows for the feeding and printing of linerless media. In this mode, the printer's functionality is the same as with the continuous or tear-off modes depending on configuration settings.
Page 8-6
LD610 User's Technical Reference
Section 8: Appendix
8. 5 BASE REFERENCE POINT
The base reference point is the point at which one determines the print and cut positions. The base reference position differs, depending on the print mode or the label pitch sensor to be used.
Continuous Mode
I-Mark I-Mark (CX-compatible)
(Base print position) Gap end Gap start
Gap
Base print position
Base print position
I-Mark
I-Mark (CX-compatible)
Gap
Base print position
Center label
Base print position
Center label
Base print position position
Center label
position
position
Cutter Mode
I-Mark I-Mark (CX-compatible) Gap
Base print position Base cut position
Base print position
Center label
Base print position Base cut position
Base cut position
LD610 User's Technical Reference
Page 8-7
Section 8: Appendix
8. 5 BASE REFERENCE POINT (cont'd)
Dispenser Mode
I-Mark I-Mark (CX-compatible) Gap
Base print and dispense position
Base print and dispense position
Base print and dispense position
I-Mark
I-Mark (CX-compatible)
Base print position
Unprintable area ( m
Base print position
Unprintable area ( m
8. 5. 1 Base Reference point Adjustment
Print Position Offset refers to the vertical and horizontal shifting of the entire print area, relative to the start position of printing (V=0, H=0), defined by default to be the bottom right hand corner of the label. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE OKI LD610
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual OKI LD610 will begin.