User manual ONE FOR ALL SV-9530

[. . . ] - On the inside of the battery compartment door you will find a label on which to write your Set-Up Codes for future reference. This you will do after setting up your ONE FOR ALL 2 remote for your devices. The Keypad Please refer to the picture of the ONE FOR ALL 2 Remote Control on Page 3. 1 2 3 4 Magic Key: The Magic key is used to set-up your ONE FOR ALL 2 Remote Control and to access special functions. Power Key: The Power key controls the same function as it did on your original remote. Device Keys: The TV & VCR keys select the home entertainment device you wish to control. [. . . ] AV The AV key operates the same function it did on your original remote control. Channel Up / Down Control: These keys control the same functions as your original remote control. Mute Key: The Mute key operates the same function it did on your original remote. Volume Up / Down Control: These keys operate just as those on your original remote. Directional Keys If available on your original remote, these keys will allow you to navigate through the menu of your device. 5 6 7 8 9 10 WWW. ONEFORALL. COM 4 The Keypad 11 OK key If your original remote control required that you press an "OK" or "ENTER" key during Menu operation, this key can be used for this function. Menu Key: Controls the same function as it did on your original remote control. 12 13 14 Exit Key: The Exit key will exit the Menu. 16:9 key In TV mode this key allows you to access the wide screen (16:9) view option of your television (if available on your original remote). VCR keys (PLAY, STOP, REW etc. ) After pressing the VCR mode key, the Playback keys operate the same functions of your Video Recorder Keys. To prevent accidental recording, the RECORD key must be pressed twice. In VCR mode the SP/LP key controls the tape speed function, the AUTO key controls the auto tracking function, just like on your original remote. Teletext Functions: After pressing the TV key, the transport keys (REW, PLAY, FF, PAUSE) are used to operate the main Teletext functions. Press and hold down MAGIC until the ONE FOR ALL 2 red light blinks twice (the red light will blink once then twice). Now press CH+ over and over, until your Television turns off (every time you press the CH+ key the ONE FOR ALL 2 will send out a POWER signal from the next code contained in the memory). You may have to press this key many times (up to 150 times) so please be patient. If you skip past a code, you can go to the previous code(s) by pressing the CH- key. Remember to keep pointing the ONE FOR ALL 2 at your Television while pressing this key. 4. 6. CH 7. As soon as your television turns off, press MAGIC to store the code. - Most TV's do not switch on pressing the POWER key. Please try pressing a "number" key or the "TV-text off" key to switch your TV back on. - If you cannot control your Television properly, please continue the Search Method, you may be using the wrong Code. - To search for the code for another device follow the instructions above only press the appropriate device key instead of TV during step 2. - If the original remote control of your Video recorder does not have a POWER key, press PLAY instead of POWER during step 5. WWW. ONEFORALL. COM 7 Code blink out (To find out which code is currently programmed) Once you have Set-Up your ONE FOR ALL 2, you can blink back your Set-up Code for future reference. Press and hold down MAGIC until the ONE FOR ALL 2 red light blinks twice (the red light will blink once then twice). [. . . ] For the second digit of your four-digit code, press 2 and count all the red blinks. For the third digit of your four-digit code, press 3 and count all the red blinks. For the fourth digit of your four-digit code, press 4 and count all the red blinks. 4. 5. 6. 7. - To blink back the code for your other devices, press the appropriate device key during step 1. Quick Code Reference Make sure you write down the codes for your devices in the boxes below and in the battery compartment for future easy reference. [. . . ]