User manual ONE FOR ALL URC 6960

[. . . ] A macro can be used to control a home theater operation, to set a favorite channel, or for other multiple functions you would like to control with one key press (see examples below). Moreover, the MACRO key can hold up to 15 key presses total. NOTE: Programming a new macro over an existing one will erase the original macro. 4. Then press SET once. NOTE: If the original remote control required pressing an Enter key to change the channel, also press the Enter key after the channel number (e. g. , 0 -3-1-Enter). 8 DEVICE HOME THEATER UNIVERSAL REMOTE CONTROL Use CH+ (or CH-) to select the next higher (or lower) channel. device. However, you may change the Volume Lock setting to Global Volume Lock so that a device's volume will be locked to one mode (e. g. , to control TV volume in all other modes). After that, if desired, you can perform Individual Volume Unlock on a selected device to set its volume control for independent operation. SOLUTION: Try all listed codes for the device brands being set up. [. . . ] Volume will again be independently controlled according to its default states for all programmed devices. CUSTOMER SUPPORT For assistance, please contact us in any of the following ways: · E-mail: ofasupport@ueic. com · Internet: http://www. oneforall. com · Consumer Help Line: (330) 405-8615 2. Press and hold SET until the LED (red light) blinks twice, then release SET. Use the Setup Codes For TV/VCR Combos (on the back) to locate the brand name and then enter the first four-digit code for your device. If performed correctly, the LED will blink twice. NOTE: If the LED did not blink twice, repeat steps 2 through 4 and try entering the same code again. INTRODUCTION The One For All 8 Device Home Theater Universal Remote Control is designed to operate up to eight home entertainment devices, including TV, video, and audio components. The remote control requires two (2) new AA alkaline batteries (not included) and easy programming to control your devices. For best results, please read and perform all instructions listed here. Also, keep these instructions for future reference. Use PIP to switch the Picture-In-Picture feature on or off (if available on your TV). Use MOVE to move the window picture to different positions in the main picture. Use SWAP to switch images and sound between the main and window pictures. Press SLEEP to activate your device's sleep timer (not available for all devices). When this feature is activated, keys will remain backlight for 5 seconds after the last key press. Use SET for all programming sequences. Example ­ Programming A Master Power Key With Instant Channel Selection A macro can be programmed to turn on and off your equipment as well. After programming, press HOME THEATER once to select the home theater mode (see Using The Home Theater Mode). Use GUIDE to display your selected device's program guide or setup menu. Use INFO to display the current channel and program information. RROUND SOUND 5. Then enter the following sequence: CBL, POWER, and 1-1 (or 0 -1- 1 if access is over 100 channels) 6. Now when you press MACRO once, the TV will turn on and tune to channel 03. Then the cable box will turn on and tune to channel 11. INSTALLING BATTERIES 1. On the remote control's back, push the tab and lift off the battery cover. Match the + and ­ marks on the batteries to the + and ­ marks in the battery case, then insert the new batteries. Test the remote control by first pressing POWER and then any mode key (e. g. , TV). If batteries are inserted correctly, the LED (red light) will blink once. NOTE: When batteries need replacement, the remote control will stop operating. Remove the old batteries and insert new ones within 30 minutes to ensure all of your programming information is restored. 1. [. . . ] Look for these exciting products at a retailer near you. PROGRAMMING DEVICE CONTROL The One For All 8 Device Home Theater Universal Remote Control is preprogrammed at the factory to operate an RCA TV and VCR, a Motorola (GI) cable box, an RCA satellite receiver, a Pioneer CD player, a Toshiba DVD player, a Pioneer audio receiver/ amplifier, and a One For All home automation device. To control devices other than the default brands, perform the following steps; otherwise skip this section: NOTE: For TV/VCR Combo control, see the next section. TROUBLESHOOTING PROBLEM: If you own a satellite that uses code 0775 (Express Vu and Echostar) and your exit key does not work, perform the following sequence to activate this feature/function. The Exit key will now correctly perform the exit feature/function on your satellite. PROBLEM: PROBLEM: LED (red light) does not blink when you press a key. [. . . ]