User manual PALSONIC HDSTB100

[. . . ] This unit does not contain any parts that can be repaired by the user. DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. - All these safety and operating instructions should be read before the product is operated. - The safety, operating and use instructions should be retained for future reference. [. . . ] The remote control may not work properly if the remote sensor window of the main unit is under direct sunlight or strong lighting. In such a case, change the angle of the lighting or STB, or operate the remote control closer to the remote sensor window. 5 Chapter 2: Introduction Remote control functional key list 16 PIP/VCR Switch between PIP and VCR for the secondary program display. Note: For PIP output or VCR output, you can only select one output at the same time. If PIP is selected, then VCR can not be selected; If VCR is selected, then PIP can not be selected. You can press PIP/VCR button to toggle and select one mode you desire. 17 PIP control buttons ON/OFF: to turn on/off PIP function. SWITCH: to swap the main and sub-pictures if the secondary display is at PIP status. Or to switch VCR program to main screen display and main program to VCR if the secondary display is at VCR status. 16 17 LIST: to display PIP (or VCR) program list. Note: when pressing PIP/VCR and PIP control buttons, within 5 seconds after corresponding OSD disappear, if you press digit buttons, DSP, ASPECT, VOLUME+/-, MUTE buttons, it will affect PIP picture (or VCR picture). The component out jacks are available when HD1 (576p), HD2 (1080i), or HD3 (720p) display format is selected. Important After you toggle the Display Format Selection Switch, you must turn off the STB and then turn on again, then the toggling can effect. 10 Chapter 3: Getting Started Connecting to a HD monitor (RGB type) Follow this diagram when connecting. Connection Antenna Rear of STB RS232 YPbPr RGB Rear of HD Ready TV Note: The YPbPr/RGB selection switch must be set to RGB. The RGB out jack is available when HD1 (576p), HD2 (1080i), or HD3 (720p) display format is selected. Important After you toggle the Display Format Selection Switch, you must turn off the STB and then turn on again, then the toggling can effect. 11 Chapter 3: Getting Started Connecting to a VCR Follow this diagram when connecting. Connections Rear of STB Note: These connections are only available when VCR is selected by pressing PIP/VCR button. Rear of VCR Connecting to an Amplifier Follow this diagram when connecting. Rear of STB RS232 OPTICAL COAXIAL Amplifier DIGITAL INPUT Connecting to an amplifier equipped with OPTICAL or COAXIAL. 12 Chapter 4: Operations Program Search You must perform the program search when using the STB at the first time. There are three ways to search programs: Quick Search, Auto Search and Manual Search. Quick Search If you live in the cities listed on the Quick Search menu, you may go ahead to select your city and start scanning all digital TV channel Signals. 1 2 3 4 5 6 7 Press MENU button to access the menu mode. Press button to select and highlight Program. Program System Password Time Quick SRCH Auto SRCH Manual SRCH Press ENTER button to enter into the Program menu. Press button to highlight Quick SRCH. Press ENTER button to enter into Quick search sub-menu. button to select the city Program System Password Time Quick SRCH Auto SRCH Manual SRCH Please Select City Adelaide Begin Cancel Move the highlight to Begin and press ENTER to start the searching. To cut off the searching during the process, highlight CANCEL and press ENTER. Searching Ch 11. . . Auto Search Auto search will automatically find all channels (digital) available through the antenna inputs, and store all the active channels in the channel list. 1 2 3 Enter into Program menu and select Auto SRCH. When channel scanning is complete, the first channel found appears on the TV screen. To cut off the searching during the process, highlight CANCEL and press ENTER. Program System Password Time Quick SRCH Auto SRCH Manual SRCH Program System Password Time Quick SRCH Auto Search Channels 6-69 Auto SRCH Manual SRCH Begin Cancel Searching Ch 27. . . 13 Chapter 4: Operations Manual Search SpeProgram Search/Channel & Program selection If desired programs can not be searched, you can make use of Manual Search. 1 2 3 4 5 6 Press MENU button to access the menu mode. Press button to select and highlight Program. Program System Password Time Quick SRCH Auto SRCH Manual SRCH Press ENTER button to enter into the Program menu. Press button to highlight Manual SRCH. Program System Password Time Quick SRCH Manually Enter Channels Auto SRCH CH No 08 Manual SRCH Freq. OK Searching. . . Press ENTER button to enter into Manual search sub-menu. Use button to move the cursor rightward or leftward and use button to select number (or directly input the number by digit buttons), then press ENTER. Now it starts searching. 7 Note: Normally it is unnecessary to input the frequency value. [. . . ] If STB is connected to your monitor or TV via YPbPr port or RGB on the back panel, the display format must not be SD. If STB is connected to your monitor or TV via YPbPr port on the back panel, the YPbPr/RGB selection switch must be flipped to the YPbPr. If STB is connected to your monitor or TV via RGB port on the back panel, the YPbPr/RGB selection switch must be flipped to the RGB. Check to make sure all the cables are installed correctly and that the proper source is selected on your TV. [. . . ]