User manual PALSONIC HDSTB200

[. . . ] High Definition Digital Receiver HDSTB200 PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL: (02) 9313 7111 FAX: (02) 9313 7555 www. palsonic. com. au PALSONIC CUSTOMER SERVICE TELEPHONE AUSTRALIA: 1300 657 888 User Manual Safety Information CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO AVOID THE RISK OF ELECTRIC SHOCK, DO NOT OPEN. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY. The lightning flash with arrowhead symbol within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and servicing instructions In the literature accompanying the appliance. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO WATER OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK. ENSURE 240V AC POWER PLUG IN FULLY INSERTED INTO THE POWER SOCKET. CAUTION: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE MANUFACTURER WILL VOID THE USER'S WARRANTY. WARNING: TO ENSURE RELIABLE OPERATION AND PREVENT THE HS-STB FROM OVER HEATING, YOU MUST REMOVE THE PROTECTIVE PLASTIC FILM FROM THE HS-STB COVER. Important Safeguards These important safeguard messages will help ensure your enjoyment and proper use of the HD-STB and accessories. Please read them carefully before you begin to operate your HD-STB product. 1. [. . . ] If you need change the display mode, press the UP and DOWN button at the front panel simultaneously for display mode change. Press UP or DOWN button at the front panel to select desired display mode. Press UP and DOWN button concurrently to confirmed display mode change. 17 Getting Started Step 8. Install Remote Control battery and Universal Code setting. Install Remote Control battery. The battery has polarity so when insert the batteries make sure the "+" and "-" terminals are oriented correctly. For more detailed information, please refer to the Remote Control Universal Code Setting section. Step 9. Check up the On Screen Display. For verify correct setting of Display Mode, you should check up the OSD from HDTV's display screen. Press Menu button on the remote control, you should check up the OSD for verify A/V connection. If you cannot find any OSD in your TV display, please check up again the Display Mode Setting and A/V connection. Step 10. Automatic Channel Search and Channel Change. Please set the time Zone and perform the Automatic Channel Search to find possible channels. If you setting up the favourite channel using Favourite Setup in the menu system, you can change the channel using "CH+" or "CH-" between selected favourite channels. Please make sure in favourite channel mode, the channel change operation is based on Favourite Setting in the internal memory. If you unmark the channel in the favourite list, you cannot access the channel using "CH+ of "CH-" button. At that time, please perform the Favourite Setup and mark the Channel in the favourite list. 18 Using the MENU System From here you can adjust whole setting and function of HD-STB. If there is no remote control activity more than 60 sec, then all menu will automatically disappear for prevent unwanted operation. 1. User Preference From here you can adjust User Preference settings concerning your TV. Preferred Audio Type (I-II) You can select desired audio signal from broadcaster. If you select Dolby Digital and broadcaster simultaneous broadcast the Dolby Digital and MPEG audio, then your HD-STB will check up the Dolby Digital audio first and decode Dolby Digital audio. If you select Dolby Digital but broadcaster broadcast MPEG audio only, then your HD-STB will check up the Dolby Digital audio first and next select MPEG audio automatically. Also you can set up Audio Preference (I-II) with I-II button on the remote control. But this change is affected to selected channel only If you change channel or turn off the HD-STB, then default audio type be selected. 6) Press MENU to exit the menu. User Preference Preferred Audio Type SD Output Aspect Ratio i-Plate Banner Duration Front Panel LED Dimmer Power Restore MPEG Dolby Digital 10 sec High Disable Preferred audio type when program contains MPEG and Dolby Digital audio 19 Using the MENU System SD Output Aspect Ratio You can select best fitting display mode for your SD TV screen. This function is available only Composite Video and S-Video output when the 16:9 source is coming from Broadcaster. [. . . ] Consult with your retailer who has local knowledge on DTV broadcasting The signal received may be too poor to allow the digital receiver to find some or all available channels or Your old antenna may not be designed to receive all DTV channels or Antenna reception performance has deteriorated due to weathering, corrosion of antenna Connections / cabling and broken elements. Please contact your local TV antenna installer. Generally, a quality suburban antenna installation consists of: (1) Separate VHF (Ch's 6-12) and UHF (Ch's 27. 69) antenna's (rule of thumb; larger antenna's with more elements capture more signal). If you live within 5-10Km of DTV transmission towers, a combined VHF/UHF antenna should be adequate. Outside this area, separate VHF and UHF antennas provide superior reception performance. [. . . ]