User manual PALSONIC MODEL 2418

[. . . ] LOCATE appliance in the room where direct light does not strike the screen. ALLOW adequate space between the appliance and the wall to permit proper ventilation. AVOID excessive warm and dusty location to prevent possible damage to the cabinet and component failure. The range of the DC power supply must be in 12V - 14V. LOCATION: 1 ANTENNA ANT. [. . . ] If you wish to change the settings, or add more channels, the method is quite straight forward. Press CHANNEL SELECTOR button on the appliance or the Remote Control Unit, the channel number will be increased or decrease as shown in the following Fig, and displayed in the upper right comer of the screen. CHANNEL INCREASE CH 0 1 8 58 59 CH CH CHANNEL SELECTION CHANNEL DECREASE (REMOTE) 0 1 8 58 59 (THE APPLIANCE) . Use the CHANNEL SELECTOR button on the Remote Control Unit to select channel. a) Single digit channel In this method, you can only select any one of 0-9 program position directly by pressing the 0-9 button accordingly. b) Two-digit channel In this method, you should press the "1-" "2-" "3-" "4-" or "5-" button at the first, then press the 0-9 button. For example, if you wish to receive channel 28, press "2" button, then press "8" button NOTE: To select two-digit channel, the second digit must be pressed within 2 seconds. * PREVIOUS BUTTON (REMOTE CONTROL UNIT) Pressing this button to select the channel that was tuned immediately before the one being watched. For example: If you are watching the program on channel 6, and the previous program you watched is on channel 15; then you can press the button to reach channel 15, press it again to return channel 6. 4 6 15 . The current band and channel position will be displayed on screen (in green). Press AUTO (AUTO PRESET) button, the appliance will search the signal of TV station in the order of VHFL, VHFH and UHF, as shown in the following, and memorise them from channel number 1 position. VHFL VHFH UHF * During presetting, the green block turns into yellow. When presetting is over, the channel position is set to number 1 automatically. NOTE: During presetting, auto presetting will be cut off if any one of STAND BY button, PRESET ON/OFF button or AUTO PRESET button is pressed. . * If "SKIP" displays on the screen, press "SKIP" button on the front panel to exit "SKIP" mode. llllllllllllll 3. Press and hold manual tuning button "FT VHFL CH CH 8 SKIP SKIP llllllllllllll " "FT " till your desired program appears. VHFH UHF 8 VHFH VHFL VHFH UHF 4. The searched program station has been memorised at the present channel position. FUNCTION: SKIP BUTTON: When CHANNEL SELECTOR button is used to select channels, the channel will be skipped if they are set to "SKIP" mode. For example: Set 2~7 channels to "SKIP" mode, the procedure of channel position increasing or decreasing. CHANNEL INCREASE CH 0 1 2 58 59 CH CH 8 CHANNEL DECREASE (REMOTE) 0 1 2 58 59 (THE APPLIANCE) . Press "SKIP" button, "SKIP" will be displayed on the screen to indicate that the channel is at "SKIP" mode. SKIP llllllllllllll 3 SKIP 4. VOLUME CONTROL SOUND CONTROL: Press the VOL button on the appliance or the Remote Control Unit to increase volume; the red block on the screen moves right. Press the VOL button on the appliance or the Remote Control Unit to decrease volume; the red block on the screen moves left. . MUTE BUTTON (REMOTE CONTROL UNIT) When there is a phone-call or a visitor, it can temporarily shut off the sound without affecting the picture. Press the PICTURE CONTROL button on the Remote Control Unit. The FUNCTION to be adjusted is selected in sequence as shown in the following chart at every press of the button. CONTRAST PICTURE COLOUR BRIGHTNESS PICTURE CONTROL (REMOTE CONTROL UNIT) . [. . . ] Press the CHANNEL SELECTOR to set your desired channel. . TIME 1 ON TIME AM 12 : 00 8 ON TIME PM 7 : 00 5. Press TIME button, the CLOCK indicator is green instead of red ON TIME function starts operating. The appliance will be turned on automatically when the clock reaches your setting time. * The ON TIME operation will be cancelled if you switch off the power before your setting time is up. [. . . ]