User manual PALSONIC MODEL 5169M

[. . . ] Preset menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Function menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Channel selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Picture and volume adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] PICTURE menu Making use of the PICTURE menu can adjust the picture effect according to your personal preference and it will be stored as picture memory mode automatically. Press the CH button to select the item (the selected item is highlighted in red). Below are the characteristics of the picture adjustment item. OSD 0 Pressing Item (BRIGHTNESS) (COLOUR) (CONTRAST) (TINT) (SHARPNESS) Green bar moving 63 VOL Darker Lighter Weaker Purplish Weaker VOL Brighter Stronger Stronger Greenish Stronger Note: * TINT is effective only in NTSC system. 2. PRESET menu PROG SKIP AFT BAND 28 OFF ON U SYS 1 AUTO SEARCH MANUAL 8 Making use of the PRESET menu can fulfil the function of auto-search, search. Press the MENU button to exit to the main menu. 1) PROG (program) Select the current program number while "PROG" is highlighted. PROG 0 1 2 99 button to 2) SKIP-ON/OFF Press CH button to highlight SKIP ON/OFF. When "SKIP ON" is set, the current channel program will be skipped. Making use of this function can skip some unwanted channel, say 5, 11, next when you press CH button to select channel, 5, 11 channel will be skipped. 0 1 4 6 10 12 * Press the channel direct select button can select the skipped channel. 3) AFT ON/OFF Making use of the AFT function can automatically fine tune the channel. Select and highlight AFT, pressing VOL button it toggles between ON and OFF. When in the process of manual search, AFT is set "OFF" automatically. 4) Band Selection Press the CH button to highlight BAND. The 5) SYS (sound system) This item is used to select sound system. Since this TV model's RF sound system is B/G only, this item gets into ineffectiveness in sound system selection. 6) Auto - search (AUTO) Press CH button to highlight AUTO. Press VOL button the set will automatically search and store the active TV signals in your local area from lower band to 9 higher band in the sequence of VL VH U with the green bar moving rightward. When a station is located, the set will store the signals with a channel number from 0. When all the signals are searched and stored, the TV returns to 0 channel automatically, auto-search is finished. * After auto-search, all programs colour system is set to AUTO and in AFT-ON mode. * During the process of auto-search, if MENU or CH button is pressed, the searching is interrupted. Press VOL button the searching begins again. 7) SEARCH Making use of SEARCH function will store a TV program at a referred channel position. Select a channel number, when SEARCH is highlighted, press VOL button, the set begins to search for signals upward or downward from current channel. When a station is located, the searching stops and the program is stored into the referred channel position. Repeat the above step and store another program signals into another position. When the searching is finished, to store the program signals you should press the MENU button to exit the menu and the program signals are stored automatically. [. . . ] Video playback The figure below shows how to connect the TV set to the video equipment. Press the AV button on the remote controller or TV/AV button on the set to select "AV" mode, "AV" and corresponding colour system will be displayed on the screen. The picture shown on the screen is the program from the video equipment 2. Recording TV program The figure below shows how to connect the TV set to the VCR. Press AV button on the remote control unit to set TV mode, and choose the desired channel. DUBBING The picture below shows how to connect TWO VCRs to the TV for dubbing one from the other. Press AV button on the remote control unit to select AV mode before dubbing, "AV" will be displayed on the screen. [. . . ]