User manual PEAVEY 5150
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual PEAVEY 5150. We hope that this PEAVEY 5150 user guide will be useful to you.
Manual abstract: user guide PEAVEY 5150
Detailed instructions for use are in the User's Guide.
[. . . ] In the "out" position the RHYTHM channel is activated and the green LED illuminates. If remote selection is desired the channel select switch must be set to the "in" position (LEAD channel).
CHAMUEL SELECTSMITCH
BRIGHTSWITCH
Activates a preset boost in the treble frequencies (6 dB at 2 kHz) and affects only the rhythm channel.
CRUNCH 'SELECTSWITCH
Boosts the gain of the rhythm channel to create a second "lead" channel. [. . . ] If it is necessary to use the 5150 without proper grounding facilities, suitable grounding adaptors should be used. Greatly reduced shock hazard exists when the unit is operated with the proper grounded receptacles.
18
STANDBY SW/TCR
Allows the 5150 to be placed in a non-operational standby mode. When the standby switch is activated the tubes remain hot and ready for instantaneous operation, eliminating warm-up time. The STANDBY LED indicator light [16] will illuminate when the amp is in the operational mode.
A
23 24
EFFECTS SEND / EFFECTS RETURN
19
POWER SW/TtN
Supplies power to the unit. Depressed to the "ON" position, the POWER LED indicator light [17] will illuminate indicating power is beina suDPlied to the unit.
Signals are supplied to outboard effects or signal processing units by patching from the EFFECTS SEND [23] output into the outboard unit(s) and back into the EFFECTS RETURN [24] input using shielded cable with l/4" phono jacks. Only non gain effects devices (chorus, reverb, delay, etc. ) should be used in the effects loop. Remote (on/off) selection of outboard effects devices can be achieved using the 5 150's footswitch.
25
PREANPOUT
This output can be used to send a preamped signal from the
5150 to a mixing console, tape
recorder, etc. , using shielded cable. Patching from the PREAMP OUT does not affect the normal operation of the amplifier.
17
lANDBY 0 POWER 0
18
BACK PANEL
ON ON
27
28
PEAVE" ELECTRONICS CDRP
m STANDBY POWER PATENT PENDlNG
19
REMOTE FOOTS WITCH JACK
Provided for the connection of the supplied remote footswitch. When the footswitch is plugged into the remote footswitch jack, the channel select switch [3] must be pressed to the "in" position for remote selection to operate. Remote selection of the LEAD or RHYTHM channel (left footswitch button) or outboard devices in the effects loop (right footswitch button) is possible with the remote footswitch.
26
sr SNAKER O U T P U T S
A
; 1. Paralleled VV' output jacks for connecting speaker enclosure(s) to the amplifier (minimum: 4 ohms). When using more than one enclosure, be sure to calculate the total impedance and set the impedance switch [28] accordingly. (See section on IMPEDANCE SWITCH. ) Important: Use only high quality, UNshielded cable for speaker connections.
28 : f IMPiEDAUCE SELECTOR SW/TCH . * . , . . . I'. , Use to select the appropriate
impedance of the speaker enclosure(s). [. . . ] tubes or meters], repair the defect in maternal or workmanship or replace the p(oduct at Peavey's optmn and provw, ed. all costs of shtppmg 11 necessary, are pad by you the purchaser THE WARRANTY REGISTRATION CARDSHOULD BE ACCURATELY COMPLETED ANDMAILEDTOAND RECEIVED BY PEAVEY WITHIN FOURTEEN (14) DAYS FROMTHE DATE OF YOUR PURCHASE In order to obtam swwce under these warrenbee. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE PEAVEY 5150
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual PEAVEY 5150 will begin.