User manual PIONEER AVH-P6400R INSTALLATION MANUAL

[. . . ] € Refer to the owner’s manual for details on connecting the power amp and other units, then make connections correctly. To protect the wiring, wrap adhesive tape around them where they lie against metal parts. € Route and secure all wiring so it cannot touch any moving parts, such as the gear shift, handbrake, and seat rails. Do not route wiring in places that get hot, such as near the heater outlet. [. . . ] € If this unit is installed in a vehicle that does not have an ACC (accessory) position on the ignition switch, the red lead of the unit should be connected to a terminal coupled with ignition switch ON/OFF operations. If this is not done, the vehicle battery may be drained when you are away from the vehicle for several hours. Please ground this lead separately from the ground of high-current products such as power amps. If you ground the products together and the ground becomes detached, there is a risk of damage to the products or fire. € Cords for this product and those for other products may be different colors even if they have the same function. When connecting this product to another product, refer to the supplied Installation manuals of both products and connect cords that have the same function. 1 Connecting the Units Connecting the power cord (1) Note: Depending on the kind of vehicle, the function of 3* and 5* may be different. This product 11 cm 5* 4* Connect leads of the same color to each other. Yellow (3*) Back-up (or accessory) Yellow(2*) To terminal always supplied with power regardless of ignition switch position. Fuse holder Red (5*) Accessory (or back-up) Fuse resistor Fuse resistor ISO connector Note: In some vehicles, the ISO connector may be divided into two. Yellow/black If you use a cellular telephone, connect it via the Audio Mute lead on the cellular telephone. 3 Subwoofer output or non-fading output (SUBWOOFER OUTPUT or NON-FADING OUTPUT) 15 cm 23 cm ENGLISH Connecting cords with RCA pin plugs (sold separately) Power amp (sold separately) Rear output (REAR OUTPUT) Front output (FRONT OUTPUT) Blue/white To system control terminal of the power amp (max. Power amp (sold separately) Power amp (sold separately) ESPAÑOL DEUTSCH System remote control The pin position of the ISO connector will differ depends on the type of vehicle. Left Front speaker Right Front speaker ITALIANO Rear speaker Blue/white (6*) Rear speaker Speaker leads White White/black Gray Gray/black Green Green/black Violet Violet/black Subwoofer : Front left + : Front left ≠ : Front right + : Front right ≠ : Rear left + or Subwoofer + : Rear left ≠ or Subwoofer ≠ : Rear right + or Subwoofer + : Rear right ≠ or Subwoofer ≠ Subwoofer NEDERLANDS Use this for connections when you have the separately available amplifier. Note: Change the Initial Setting of this Product (refer to the Operation Manual). 2 4 Connecting the Units Connecting the power cord (2) When using this product with a back-up camera, automatic switching to VIDEO video when the gear shift is moved to the REVERSE (R) position is possible. This product Note: • When you have completed lead wire connection, perform [VIDEO SETTING] correctly while referring to the Operation Manual. € It is necessary to set to [BACK UP CAMERA] in the [VIDEO SETTING] when connecting the back-up camera. Power cable Fuse resistor Violet / white Of the two lead wires connected to the back lamp, connect the one in which the voltage changes when the gear shift is in the REVERSE (R) position. This connection enables the unit to sense whether the car is moving forwards or backwards. This lead must be connected to the power supply side of the parking brake switch. Parking brake switch Power supply side Connecting method Ground side Note: • The position of the parking brake switch depends on the vehicle model. [. . . ] 8 DIN Front/Rear-mount This unit can be properly installed either from “Front” (conventional DIN Front-mount) or “Rear” (DIN Rear-mount installation, utilizing threaded screw holes at the sides of unit chassis). (When reattaching the frame, point the side with a groove downwards and attach it. Holder After inserting the holder into the dashboard, then select the appropriate tabs according to the thickness of the dashboard material and bend them. 11 NEDERLANDS 10 Installation 7 When the installation space is not very deep When installing in a shallow space, secure with side brackets (small). [. . . ]