Detailed instructions for use are in the User's Guide.
[. . . ] iPower System Software Release Bulletin and Installation Instructions
Version 6. 2. 0
Last Updated: 12/16/2004
To ensure that you have the latest version of this document, go to http://www. polycom. com
Copyright © 2004: Polycom, Inc. Polycom, Inc. , 4750 Willow Road, Pleasanton, CA 94588 www. polycom. com Polycom and the Polycom logo are registered trademarks of Polycom, Inc. Concorde, Global Management System, ImageShare, iPower, LiveManager, Montage, NetConference, PathNavigator, People+Content, PVX, SureConnect, PowerMic, ProMotion, Siren, System 4000, Venue, ViaVideo, ViewStation, Visual Concert and VSX are trademarks of Polycom, Inc. All other product names are the trademarks of their respective owners. [. . . ] If no Content is being shown, far-end video is recorded.
The system may not display VCR video while fast-forwarding a tape.
Some VCRs may not appear on the People and Content list unless they are playing a tape. You can use AdminTools to configure the system to include the VCR on the People and Content list, even if no signal is detected. When using the Digital Conference Recording feature on iPower systems with Windows XP, a "Browse for Folder" error message may appear when attempting to select the folder destination for the recorded stream. If this happens, click OK in the error message window, and select a new folder location from the screen that follows.
Calling
When the iPower system is showing Content in a non-Dual Images call, the iPower system cannot adjust its People camera. In this software version, you cannot make 2x64 non-dialed (DCEsignaled or DCE-dedicated) calls. In a multipoint call that includes the ViewStation FX, the iPower system cannot control the presenter's camera During a call, you may experience substantial delays in T. 120 activities when the far end takes control. To make a loopback call, select a rate less than or equal to the number of ISDN lines connected. When you are in a loopback call, the system does not allow you to select the Content source. Conference Statistics and Operating Statistics may report a video error when you add or remove Content from a videoconference. The iPower system does not transmit video in an H. 263 ISDN QCIF call to a PictureTel Concorde·4500. If an iPower system receives a still-image graphic from another type of system, the iPower system displays the graphic until the end of the call. If an iPower system receives a still-image graphic from another type of system and you switch the image from the main video window to the PIP, the PIP displays a black screen. Use a voice alias or E. 164 address when placing Voice over IP (VoIP) calls. Otherwise, the system may treat an incoming or outgoing call as a video call (for example, it may automatically answer the call if you configured auto-answer for video calls). If a call is sent through a gateway or MCU that does not support People and Content, the Content video quality is reduced, even if both endpoints support People and Content. Configure a gatekeeper before attempting to make gateway calls.
In a PathNavigator Conference on Demand call, only the local system is included in the Conference Sites list. Conferences hosted by an Avaya MCU do not support the Browse function. If you select Remote Control > Far-End Camera and turn off Picture-in-Picture (PIP) from the iPower collaboration application Options menu, you are unable to switch to near-end camera control. H. 323 MCU, the call does not connect when dialed with an E. 164 address that starts with the digit "1". When you use the on-screen Camera Controls, you cannot use the onscreen cursor for functions outside of the Camera Controls, such as muting. If you attach V. 35/RS-449 cables to the system when it is powered on, the system may interpret any signal changes as an incoming call. To address this issue, power off the system before connecting the cables. In a V. 35 DCE-Signal call to a Concorde·4500 system, the iPower system may hang up the call and not reconnect. [. . . ] See the section "Reinstalling the iPower 900 or 9000 System Software" for more information. To reinstall the iPower 900 system software to version 5. 0, use the boot floppy and the two-CD set with part numbers 5151-50783-001/A and 5151-50784-001/A (model number 2200-51032-001). To reinstall the iPower 9000 system software to version 6. 0, use the two-CD set with part numbers 2151-50356-003/A and 2151-50357003/A (model number 2200-51033-001).
Before You Upgrade the iPower Software
Before you upgrade the iPower software to Version 6. 2, make sure you do the following: 1. If your system is set up for Auto Logon, use AdminTools to configure the system to use Standard Windows Logon, and restart the system. [. . . ]