User manual RICOH AFICIO AP2610 AP2610 SET UP GUIDE

[. . . ] Setup Guide For safety, please read this manual carefully before you use this product and keep it handy for future reference. Introduction This manual contains detailed instructions on the operation and maintenance of this machine. To get maximum versatility from this machine all operators should carefully read and follow the instructions in this manual. Please read "Safety Information" in this manual before using this machine. It contains important information related to USER SAFETY and PREVENTING EQUIPMENT PROBLEMS. [. . . ] the adhesive tapes and the packing material. on both sides, align the catches with the holes on the printer and insert. C Remove ZCEX300J ZGDX170J 36 1-bin Shift Sort Tray Type 2600 F Slide the upper tray into the 1-bin Shift Sort Tray. 2 ZGDX180J G Attach the interface cable to the printer. H Plug the printer's power cord back into the wall outlet, and then turn on the power switch. Note After installing the last option that you want, print the configuration page to confirm the installation. If the new device is listed in the column of configuration options, then it has been properly installed. For more information about printing the configuration page, see "Printing the Configuration Page" in the Printer Reference on the CD-ROM labeled "Operating Instructions". 37 Installing Options CS380 (Mailbox) Important If you attach the Mailbox and the Paper Feed Unit, the Paper Feed Unit must be attached prior to attaching the Mailbox. D Remove printer. the upper cover of the 2 The Mailbox and the 1-bin Shift Sort Tray cannot be attached to the printer at the same time. Check the printer nameplate to confirm the model code. Note The upper cover that is removed, is not used when attaching the Mailbox. A Check the contents of the box for the following items: · Mailbox · Output Trays (4pcs) · Output Tray Number Seal · Installation Guide ZGDH170J B Confirm that C Remove the followings are true: · The power switch is turned off. the adhesive tapes and the packing materials. E Holding the Mailbox on both sides, align the catches with the holes on the printer and insert. R CAUTION: · When lifting Mailbox, hold it on both sides. Holding underneath the Mailbox may cause injury to the hands if the Mailbox and the printer. ZCEX451J ZGDX190J 38 CS380 (Mailbox) F Slide the output tray into the lower side of the Mailbox first. 2 ZGDX200J G Slide the other output trays into the Mailbox from the bottom. printer. H Attach the interface cable to the I Plug the printer's power cord back into the wall outlet, and then turn on the power switch. Note After installing the last option that you want, print the configuration page to confirm the installation. If the new device is listed in the column of configuration options, then it has been properly installed. For more information about printing the configuration page, see "Printing the Configuration Page" in the Printer Reference on the CD-ROM labeled "Operating Instructions". 39 Installing Options 2 40 3. Configuring the Printer for the Network Make the network settings below depending on the network interface you use. · Ethernet: Make the settings in p. 41 "Ethernet Configuration", and then see p. 51 "Installing the Printer Driver and Software". · IEEE 1394: Make the settings in p. 45 "IEEE 1394 Configuration", and then see p. 51 "Installing the Printer Driver and Software". · Wireless LAN: Make the settings in p. 48 "IEEE 802. 11b (Wireless LAN) Configuration", and then see p. 51 "Installing the Printer Driver and Software". Note The optional Network Interface Board is necessary to use Ethernet with Basic model printer. The optional 1394 Interface Unit is necessary to use IEEE 1394. The optional 802. 11b Interface Unit is necessary to use the wireless LAN. Ethernet Configuration Configure the printer for the network using the printer's control panel. The following table shows the control panel settings and their default values. These items are included in the "Host Interface" menu. Reference For information about configuring the computer for the network, see the Network Printing Guide on the CD-ROM labeled "Operating Instructions". Setting Name IP Address Subnet Mask Gateway Address Network Boot Frame Type (NW) (Frame type NetWare) Active Protocol Value 011. 022. 033. 044 000. 000. 000. 000 000. 000. 000. 000 None Auto TCP/IP NetWare NetBEUI AppleTalk Ethernet *2 LAN Type *1 *2 *3 *3 *1 *1 *1 *1 For information about "Host Interface" menu, see "Host Interface Menu" in the Printer Reference on the CD-ROM labeled "Operating Instructions". Auto Ethernet means that this protocol is active. Appears only when both the Network Interface Board and the 802. 11b Interface Unit are installed. 41 Configuring the Printer for the Network } A Press {Menu}. On Line Menu } E Press {Enter #}. The following message appears on the panel display. Job Reset Escape Network Setup: IP Address Form Feed Enter F Select use. Data In ZFDP020N the protocol you want to 3 Power Error "Menu" appears on the panel display. B Press {U} or {T} to display "Host Interface" menu. Note Do not select protocols that are not used on your network. A Press {U} or {T} to display "Active Protocol". Menu: Host Interface } C Press {Enter #}. On Line Menu Network Setup: Active Protocol B Press {Enter #}. } The current setting appears on the panel display. Job Reset Escape Active Protocol: TCP/IP C Press {Enter #}. } D Press {U} or {T} to select "Active" or "Not Active", and then press {Enter #}. } E Set other protocols you need to set in the same way. Note Leave unused protocols "Not Active". Form Feed Enter Power Error Data In ZFDP060N The following message appears on the panel display. Host Interface: I/O Buffer D Press {U} or {T} to display "Network Setup". Host Interface: Network Setup 42 Ethernet Configuration G If you use TCP/IP, assign the IP address to the printer. Note To get the IP address for the printer, contact your network administrator. E Repeat steps C and D to enter the IP address. IP Address: 192. 168. 000. 011 Check if the pointer (k) is at the rightmost position, and press {Enter #} to register the IP ad} dress you selected. A Press {U} or {T} until the following message appears. Network Setup: IP Address B Press {Enter #}. [. . . ] The [WIN9X_ME] folder, inside the [PS] folder is for the Windows 95/98/Me operating system. Use the folder at this level that is appropriate for the operating system you are using. The third folder, "(Language)" may be substituted by an appropriate language name. For PageMaker 6. 0 default installation, the folder is "C:\PM6\RSRC\PPD4", and for PageMaker 6. 5 default installation, the directory is "C:\PM65\RSRC\USENGLISH\PPD4". [. . . ]