User manual RICOH AFICIO 2515 COPY REFERENCE

[. . . ] It contains important information related to USER SAFETY and PREVENTING EQUIPMENT PROBLEMS. Notes Some illustrations may be slightly different from your machine. For details, please contact your local dealer. Operator Safety This machine is considered a CDRH class I laser device, safe for office/EDP use. The machine contains a 5-milliwatt, 760-800 nanometer wavelength, GaAIAs laser diode. Direct (or indirect reflected ) eye contact with the laser beam might cause serious eye damage. [. . . ] Note The maximum copy quantity can be set between 1 and 99 (default: 99). To change the number entered, press the {Clear/Stop} key and enter the new number. C Make sure that there are no previous settings remaining. Note To clear settings, press the {Clear Modes} key. D Set your originals. Reference See P. 21 "Setting Originals". G Press the {Start} key. } The machine starts copying. Note To stop the machine during the multi-copy run, press the {Clear/ Stop} key. E Set the desired settings. To return the machine to the initial condition after copying, press the {Clear Modes} key. For Type 1 without the optional 16MB copier memory unit, you cannot copy more than 1 page from the document feeder. 19 Copying - System Reset The machine returns to its prioritized mode automatically after your job is finished, after a certain period of time. This function is called "System Reset". Note You can change the System Reset time. See "3. System Reset" in the System Settings manual. 2 - Auto Off The machine turns itself off automatically after your job is finished, after a certain period of time. This function is called "Auto Off". Note How to exit Auto Off mode depends on your machine configuration: · Copier only -- press the main power switch · Copier and fax or printer -- press the operation switch You can change the Auto Off time. See "6. Auto Off Timer" in the System Settings manual. 20 Setting Originals Setting Originals Limitation Set originals after correction fluid and ink has completely dried. Not taking this precaution could mark the exposure glass and cause marks to be copied. Note Basically the originals should be aligned to the rear left corner. However, some copy functions may produce different results depending on the direction of the originals. This applies to the following paper sizes: Metric version Inch version A4 KL, B5JIS KL, A5 KL 81/2" × 11" KL, 51/2" × 81/2"KL (document feeder) Inch version Where original is set Exposure glass Paper size and direction 11"× 17"L, 81/2" × 14" L, 81/2" × 13" L, 81/2" × 11" KL Document feeder 11"×17"L, 81/2" × 14" L, 81/2" × 13" L, 81/2" × 11" KL, 51/2" × 81/2"KL For some originals, the original size might not be detected correctly. If you specify all papers trays as containing special paper, you cannot use the Auto Paper Select function. 26 Basic Functions A Select the copy paper. Auto Paper Select A Make sure that "Auto Paper" (Auto Paper Select) is selected. Original orientation Paper orientation Rotates the image and copies it R R GCROTA0E 2 Manual Paper Select A Select the paper tray or bypass tray by pressing the {Select Paper Tray} key. } Limitation You cannot use the Rotated Copy function when enlarging onto B4JIS or A3 size paper. In this case, set your original in the landscape direction. You cannot rotate: Original Size and Direction A4, B5JIS, or A5 portrait *1 However, you can rotate: A4, B5JIS, or A5 landscape when enlarging to Copy paper Size and Direction B4JIS, A3 *1 when enlarging to B4JIS, A3 - Rotate Copy (Type 1 requires the optional 16MB copier memory unit) If the direction in which your original is set (landscape or portrait) is different from the paper you are copying onto, this function rotates the original image by 90° and fits it on the copy paper. This function works when Auto Paper Select or Auto Reduce/ Enlarge are selected. See "Auto Paper Select" in P. 26 "Selecting Copy Paper" and P. 28 "Auto Reduce/Enlarge". *1 For inch version, 11" × 17", 81/2" × 14", 8 1/2" × 13", 81/4" × 14", 81/4" × 13" and 8" × 13". 27 Copying Auto Reduce/Enlarge The machine can choose an appropriate reproduction ratio based on the paper and original sizes you select. You can change the reproduction ratio from 50 ­ 200 %. For some originals, the original size might not be detected correctly. See P. 11 "Sizes Difficult to Detect". 2 A Press the {Auto R/E} key. Note When you use Auto Reduce/Enlarge, refer to the following table for possible original sizes and directions: B Select the paper tray by pressing the {Select Paper Tray} key. } Metric version Where Original size and original is set direction Exposure glass Document feeder A3L , B4JIS L, A4 KL, B5JIS K, 81/2" × 13" L A3 L, B4JIS L, A4 KL, B5JIS KL, A5 KL, 81/2" × 13"L C Press the {Start} key. } Inch version Where Original size and direcoriginal is set tion Exposure glass Document feeder 11" × 17" L, 81/2" × 14" L, 81/2" × 13" L, 81/2" × 11" KL 11" × 17"L, 81/2" × 14" L, 81/2" × 11" KL, 51/2" × 81/ 2" KL 28 Sort Sort Type 1 requires the optional 16MB copier memory unit. [. . . ] Otherwise a fire or an electric shock might occur. · Do not place the equipment on an unstable or tilted surface. If it topples over, it could cause injury. 5 R CAUTION: · Before moving the equipment, be sure to pull all four handles fully out. Not doing this may result in an injury, such as getting your fingers pinched. After moving the equipment, return the four handles to their original positions. · When the optional paper tray unit is installed, do not push the upper part of the main unit horizontally. [. . . ]