User manual RICOH AFICIOMP C5501A

[. . . ] In no event will the company be liable for direct, indirect, special, incidental, or consequential damages as a result of handling or operating the machine. Software Version Conventions Used in This Manual · · NetWare 3. x means NetWare 3. 12 and 3. 2. NetWare 4. x means NetWare 4. 1, 4. 11, 4. 2 and IntranetWare. Trademarks Microsoft®, Windows® and Windows NT® are registered trademarks of Microsoft Corporation in the United States and/or other countries. Apple, AppleTalk, EtherTalk, Macintosh, Mac OS , and TrueType are trademarks of Apple Computer, Inc, registered in the United States and other countries. [. . . ] msh> access 1 range6 2001:DB8::100 2001:DB8::200 IPv6 access mask Configuration msh> access mask6 "baseaddress prefixlen" · The star mark represents a target number between 1 and 5. (Up to five access ranges can be registered and selected. ) Example: to specify accessible IPv6 addresses to 2001:DB8::/32 msh> access 1 mask6 2001: DB8:: 32 Access control initialization msh> access flush · Use the "flush" command to restore the default settings so that all access ranges become "0. 0. 0. 0" for IPv4, and "::" for IPv6. Note The access range restricts computers from use of the machine by IP address. If you do not need to restrict printing, make the setting "0. 0. 0. 0" for IPv4, and "::" for IPv6. Valid ranges must be from lower (start address) to higher (end address). If you are running IPv4 or IPv6, up to five access ranges can be registered and selected. IPv6 can register and select the range and the mask for each access ranges. You cannot send print jobs, or access Web Image Monitor and diprint from a restricted IP address. 60 Remote Maintenance by telnet appletalk Use the "appletalk" command to view and configure Appletalk parameters. IPv6 address mask settings msh> authfree "ID" mask6_ addr1 masklen Parallel/USB settings msh> authfree [parallel| usb] [on|off] To enable authfree, set to "on". Authentication exclusion control initialization msh> authfree flush Note For IPv4 and IPv6, up to five access ranges can be registered and selected. View settings msh> appletalk · [2] means "active" and [0] means "inactive". Changing PAP timeout configuration msh> appletalk ptimeout value > 0 · Timeout value becomes effective. msh> appletalk ptimeout value = 0 · Timeout value becomes ineffective. 2 autonet Use the "autonet" command to configure AutoNet parameters. authfree Use the "msh> set bonjour" command to display and configure authentication exclusion control settings. View settings The following command displays the current AutoNet settings: msh> autonet Configuration You can configure AutoNet settings. msh> autonet {on|off} · {on} means "active" and {off} means "inactive". · ip1394 can be specified only when the IEEE 1394 interface is installed. · wlan can be specified only when the IEEE 802. 11 interface is installed. Interface name ether ip1394 wlan Interface configured Ethernet interface IEEE 1394 interface IEEE 802. 11 interface DNS server address selection msh> dhcp dnsaddr {dhcp | static} · Specify whether to obtain the DNS server address from the DHCP server or use the address set by a user. · To obtain the DNS server address from the DHCP server, specify "dhcp". Domain name selection msh> dhcp domainname {dhcp | static} · Specify whether to obtain the domain name from the DNS server or use the domain name set by a user. · To obtain the domain name from the DHCP server, specify "dhcp". To use the domain name set by a user, specify "static". Reference p. 119 "Using DHCP" p. 65 "dns" p. 67 "domainname" Current interface priority configuration display msh> dhcp priority Interface priority configuration msh> dhcp priority "interface _name" · You can select which interface has DHCP parameter priority. · Priority settings are available when multiple interfaces are installed. 64 Remote Maintenance by telnet diprint The direct printing port enables direct printing from a network-connected computer. Use the "diprint" command to change direct printing port settings. dns Use the "dns" command to configure or display DNS (Domain Name System) settings. View settings The following command displays the current direct printing port settings: msh> diprint Example output: port 9100 timeout=300(sec) bidirect on con multi apl async · The "port" specifies the port number of the direct printing port. · The "bidirect" setting indicates whether the direct printing port is bidirectional or not. Setting timeout msh> diprint timeout [30~ 65535] · You can specify the timeout interval to use when the printer is expecting data from the network. [. . . ] Also, set the correct information for the connected devices using the I/O settings of ScanRouter V2 Administration Utility. Important If the machine is set up to connect to the delivery server via a dial-up router, the router will dial and go online whenever a connection to the delivery server is made. Telephone charges may be incurred. When connected to a computer that uses dial-up access · Do not install ScanRouter V2 Professional on a computer which uses dial-up access. · When using ScanRouter V2 Professional, DeskTopBinder Lite/Professional, Auto Document Link, or a TWAIN driver on a computer with dial-up access, a dial-up connection may be performed when connecting to the delivery server and other equipment, depending on the setup. If the computer is set up to connect to the Internet automatically, the confirmation dialog box will not appear, and telephone charges may be incurred without your being aware of it. [. . . ]