User manual RICOH AP505

[. . . ] OPERATING INSTRUCTIONS Printer Reference Read this manual carefully before you use this product and keep it handy for future reference. For safety, please follow the instructions in this manual. RICOH COMPANY, LTD. 15-5, 1 chome, Minami-Aoyama, Minato-ku, Tokyo Telephone: Tokyo 3479-3111 RICOH COLOR LASER AP505 OPERATING INSTRUCTIONS Overseas Affiliates U. S. A. RICOH CORPORATION 5 Dedrick Place West Caldwell, New Jersey 07006 Phone: +1-973-882-2000 The Netherlands RICOH EUROPE B. V. Groenelaan 3, 1186 AA, Amstelveen Phone: +31-(0)20-5474111 United Kingdom RICOH UK LTD. [. . . ] If you fail again, contact your sales or service representative. 10 Installing the Printer Hard Disk Type505 Installing the Printer Hard Disk Type505 R CAUTION: · Make sure to turn off the printer D Make sure that the projection of and wait for about 30 minutes before installing options. Not waiting for the printer to cool down can result in a burn. Note Ì For this printer, use only Printer Hard Disk Type505. the connector of the hard disk is on the top. Attach the connector to the slot while holding the hard disk. 2 A Check the contents of the box for the following items. · Printer Hard Disk Type505 · Installation Guide · Screws (3 pcs) TFWX600E B Turn E Set the hard disk in the lower left off the printer's power switch and remove all cables and cords from the printer. screws and remove the back plate. C Remove corner at the rear of the printer, as shown in the illustration. Make sure that the screw holes of the hard disk align with the screw holes of the printer. And fasten it with the screws that are enclosed in the box using the screw driver. TFWX186E TFWX610E Note Ì A coin can be used to remove the screws. 11 Installing Options F Attach the back plate to its original position, and fasten it with screws that were removed in step C. J When initialization finishes, the READY following message appears on the panel display. 2 K Print a configuration page to confirm that the hard disk is properly installed. Reference For more information on the configuration page, see the "Getting Started". Note Ì If the hard disk is not properly installed, repeat steps B to K again. Important Ì To make the printer recognize the installed option properly, you must set up the option with the printer driver. See the "User's Guide" for further details. TFWX196E Note Ì A coin can be used to fasten the screws. G Plug the printer's power cord back into the printer and the wall socket. The following message appears on the panel display. H After installing the hard disk, ini- PRESS ENTER TO INITIALIZE DISK I Press {Enter}. The printer starts initializing the hard disk. The following message appears on the panel display. INITIALIZING 12 Installing the Paper Feed Unit Type305 Installing the Paper Feed Unit Type305 R CAUTION: · It is recommended that at least C Move the printer to make installing space. two persons are used to lift the machine. Otherwise, the machine might fall and cause personal injury. · When lifting the machine, use the inset grips on both sides of the machine. · When moving the printer, be sure to keep it level to avoid spilling the fuser oil. Otherwise, the oily surfaces can create the danger of slipping and personal injury. Important Ì If your printer is equipped with the optional tray, do not pull out more than one tray with paper at a time. Note Ì It is impossible to install more than two paper feed units to your printer at a time. 2 TFWH100E Important Ì Be careful to lift the printer as the right front side of the printer is significantly heavier than the left front side. D Remove the paper feed unit from the box, and remove the styrofoam packing and the bag from the side covers. A Check the contents of the box for the following items. · Paper Feed Unit Type305 · Installation Guide TFWP050E B Turn off the printer's power switch and remove all cables and cords from the printer. 13 Installing Options E Remove both pieces of adhesive tape. I Place the printer on the paper feed unit. Align the printer onto the 4 upright pins on the paper feed unit and then lower it gently. 2 TFWP060E F Pull out the paper tray, and remove the padding. moved in step B. TFWP100E J Connect all of cables that were reK Plug the printer's power cord back into the printer and the wall socket. firm that the paper feed unit is properly installed. TFWP070E L Print a configuration page to conReference For more information on the configuration page, see the "Getting Started". Note Ì If the paper feed unit doesn't work, follow the above instructions to reinstall it. If it still doesn't work, contact your sales or service representative. [. . . ] D Replace the ventilator hole cover onto the printer. TFWX320E D Replace the ozone filters inside the printer. (There are two filters. ) A Open the front cover by pushing the front cover release button. D Close the front cover. Make sure that the front cover close properly. E Turn on the printer's power switch. Note Ì After replace the fuser oil bottle, it takes a few minutes until the message clears. TFWX080E B Grasping the ozone filter by its tab, remove it from the printer. TFWX310E 52 Replacing Consumables Replacing the Waste Toner Bottle and Charger You should replace waste toner bottle and charger whenever the following messages appear on the panel display. A Turn on the printer's power switch. the front cover release button. B Open the front cover by pushing WASTE TONER ALMOST FULL WASTE TONER FULL R WARNING: · Do not incinerate spilled toner TFWX080E 4 C Hold the inset grips (green part) of the photoconductor unit, and pull the top side of the photoconductor unit forward. or used toner. [. . . ]