User manual RICOH C410DN Installation Guide

[. . . ] Turn the green lever clockwise to lock the unit. Ferrite Core x 2 · Be sure to remove all four strips of tape from the photo conductor unit to avoid malfunction. Be careful not to let it touch your hands or clothes. Caution · Do not handle the plug with wet hands. · Keep the machine in an area that is within optimum environmental conditions. Operating the machine in an environment that is outside the recommended ranges of humidity and temperature can cause an electrical fire hazard. [. . . ] If your skin comes into contact with toner, wash the affected area thoroughly with soap and water. Hot water will set the toner into the fabric and may make removing the stain impossible. LOADING PAPER AET133S Load the new paper stack print side up, making sure the paper is flush against the paper guides. Adjust the paper guides to close any gaps. · Make sure the power cable is plugged securely into the wall outlet. · Turn the power switch off when plugging and unplugging the power plug. Turn the power switch to " "On. AET032S Be sure to read the label, which is attached on the front surface of the printer. This warns you that ink-jet paper cannot be used with this printer. First, install the yellow toner cartridge. Holding the toner cartridge horizontally ( ) with the locking lever on the upper side, install the toner cartridge bottom first, and then move the locking lever to the triangle mark ( ). The following describes how to load paper into the standard paper tray (Tray 1). Caution · Do not pull out the paper tray forcefully. If you do, the tray might fall and cause an injury. AET044S · When you first use this printer, use the four toner cartridges supplied with the printer. AQC028S · The toner cartridges that comes with the printer will allow you to print up to about 3, 000 pages. These numbers were obtained from printing A4 5% charts, but the actual number of pages will vary depending on the paper type, size, contents, and settings. · The toner cartridge for replacement comes in two types for different number of printable pages: 15, 000 pages and 5, 000 pages. However, if there is a problem, contact the dealer where you purchased the printer. · Toner cartridge mouths may become dirty during quality inspection. · To avoid paper jams, make sure paper is not stacked above the limit mark inside the tray. · Do not mix different types of paper in a single paper tray. AQC030S Lift the front of the paper tray (Tray 1), and slowly slide the paper tray back, until it stops. Make sure the tray is fully inserted to prevent paper jams. The power indicator on the control panel lights up. Slowly slide out the paper tray (Tray1), until it stops. Then, lift it slightly, and then pull it out completely. AQC009S · Wait until "Ready" appears on the display panel. This noise does not indicate a malfunction. · Do not turn off the power switch until initializing is completed. Doing so results in malfunction. AET045S AET041S Place it on a flat surface. · For details about usable types of paper, see "Loading Paper", Hardware Guide. Next Sheet CLP30DN/CLP27DN/C7531dn/C7526dn/LP231cn/LP226cn/Aficio SP C411DN/Aficio SP C410DN Quick Installation Guide 1/2 Quick Installation Guide 2/2 Test Printing The following explains the procedure for test printing of the configuration page. Test printing in order to verify that the printer is working normally. Test printing checks printer performance only; it does not test the connection to the computer. Quick Instration Guide Network Connection Follow the procedure below to connect the printer to the computer through the network. Prepare the hub and other network devices before connecting the 10 BASET or 100 BASE-TX cable to the machine's Ethernet port. Selecting the Display Language Select a language using the procedure described here. If you want to use the display in English, the following procedures are unnecessary. Reading the LED Lamps For standard ethernet port Ethernet Configuration Make the following network settings according to the network interface you are using. You can use SmartDeviceMonitor for Admin or a Web browser to make IP address-related settings in a TCP/ IP-capable environment. Press the {Menu} key. } · The default setting is English. K C M Y AQC001S Press the {Menu} key. [. . . ] · Select a printer to whose IP (IPv4) address is displayed in [Connect To] to install SmartDeviceMonitor for Client when using TCP/IP. Insert the CD-ROM into the CD-ROM drive. The installer starts. If this happens, launch "Setup. exe" on the CD-ROM root directory. · Quick Install is not available unless bidirectional communication between the printer and computer is enabled via parallel connection. For details about bidirectional communication between printer and computer, see "Printing with Parallel Connection", Software Guide. Select the network protocol using {} } or {}, and then press the {OK} key. } } Select [Specify] using {} or {}, and } } then press the {OK} key. [. . . ]