User manual RICOH FAX1700

[. . . ] FAX1700L RICOH Read the safety instructions on page i to iv Operator's Manual Optional equipment PAPER FEED UNIT TYPE 70 A paper feed unit can be added to the base machine. FAX EXPANSION CARD TYPE 20 A 2-Mbyte memory card can be added. Caution Use of control or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure Shielded interconnect cables must be employed with this equipment to ensure compliance with the pertinent RF emission limits governing this device. In accordance with ISO 7001, this machine uses the following symbols for the main switch: I means POWER ON J means POWER OFF WARNING This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the machine. Operator Safety This machine is classified as class 1 laser device according to EN60825. [. . . ] However, the fax machine will not print incoming messages right away, it will store them in memory and print them out after the roller warms up. Letting the heating roller cool halfway reduces the amount of electricity the fax machine consumes, but not as much as letting it cool to room temperature. On the other hand, since warming up takes only a short time, incoming fax messages can be printed right away. If your fax machine enters saving energy mode, SAVING ENERGY appears on the display. How to start the saving energy mode Your machine will enter the saving energy mode when machine is not used for 5 minutes. If you want to change the five minute period to one or three minutes, or if you do not want your machine to enter the saving energy mode automatically, please contact your service representative. How to exit the saving energy mode Your machine exits from the energy saving mode. Ë When a fax is received. (If the night timer is on, the message will printed out after the night timer ends. ) 42 Saving Energy OTHER FEATURES You can still send a fax while the machine is in saving energy mode. programming) by first holding down a key to switch to standby mode. Which saving energy mode is best for you? You have two choices: You can let the roller cool to room temperature or you can let it cool to the midpoint. To choose which of the two settings you would prefer, set the user parameter switch. When you allow the roller to cool to room temperature, energy savings are at a maximum and printing will take a little longer since the roller will take more time to come to printing temperature. When you select the midpoint, some energy savings will still be achieved and printing will occur more rapidly. Switch 05 bits 6 & 7 Letting the heating roller cool to room temperature: Bit 6 at 0, Bit 7 at 0 Letting the heating roller cool halfway: Bit 6 at 1, Bit 7 at 0 Saving Energy with the Night Timer You can set sleep time to let the machine go to saving energy condition and set the wake up time when it returns to standby mode the next morning. During this Night Timer mode, a fax message received is stored in the memory and will be printed automatically the next morning after the wake up timer is activated. As a typical example, you could program the heating element inside the printer to stay off at night and over the weekend. (You can program different settings for every day of the week. ) To use the Night Timer, you must: 1. Switch the Night Timer feature on. 43 OTHER FEATURES Saving Energy Setting the Timer (Function 71) Caution: While the night timer is active, all incoming calls are refused if the memory fills up. Example: For Tuesday, set the Night Timer to switch the heater on at 9 am and off at 6 pm. 1 2 3 4 5 6 7 Press Function, 6 and enter access code 2 2 2 2. Press Yes. SET NIGHT TIMER Y/N SET TIMER SUN Y/N/j k Use the j and k keys to scroll through the days of the week. Press Yes. SET TIMER TUE Y/N/j k TIMER#1 TUE /#/Y ON FROM 00:00 There are two timers for each day, each with an ON/OFF setting. "ON" means that the heater will switch on at the time indicated. "OFF" means that the heater will switch off at the time indicated. Input the time(9:00): Press 0, 9, 0, and 0 from the key pad. TIMER#1 TUE KPAD/Y ON FROM 00:00 TIMER#1 TUE /#/Y ON FROM 09:00 44 Saving Energy OTHER FEATURES TIMER#2 TUE /#/Y 8 Press Yes. [. . . ] The voltage drop introduced by this apparatus into the loop connection between the main telephone and the network at a current of 40ma d. c. Only apparatus conforming with BS6301 or EN41003 may be connected to the series socket. Any interconnection between the above socket and other connections, directly or by the way of other apparatus, may produce hazardous conditions on the BT network. Advice should be obtained from a competent engineer before any such connection is made. [. . . ]