User manual RICOH FW870

[. . . ] INMIMI FW870 Operating Instructions I In accordance I for the main switch: with ISO Standard 7001, this machine uses the following-- symbols 0 Q) I means POWER ON. I I For good copy quality, Ricoh recommends Ricoh shall not be responsible for any damage or expense that may result from the use of parts other than genuine Ricoh parts in your Ricoh office product. I Note: Some illustrations may be slightly different from your machine. 1 115 V, 60 HZ, 12A Power Source: Please make sure to connect the power cord to a power source as above. For details about po wer connection, see paqe xx. @ Copyright 1996, Ricoh Co. , Ltd. Note to users in the United States of America Warning: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. [. . . ] The copier starts copying. Do not release the original until it is fed into the copier. Preset Cutting This function cuts roll paper in a selected length. Depending on the roll width, it is cut in the following standard lengths: Metric version: Roll width 841 mm Preset length 1, 189 mm 594 mm 841 mm 420 mm 594 mm 297 mm 420 mm Paper size and direction A0 K A1 L A1 K A2 L A2 K A3 L A3 K 594 mm 420 mm 297 mm 210 mm 297 mm A4 K COPYING 15 COPYING ONTO ROLL PAPER Inch version: Roll width 36" Preset length 48" 24" 36" 18" 24" 12" 18" Paper size and direction EK DL DK CL CK BL BK 24" 18" 12" 9" 12" AK 1 Press the Cut Select key to display a length of the "Preset Cut". 2 Set the original guide to match the original width and direction. 16 COPYING COPYING ONTO ROLL PAPER 3 Insert the original lightly along the original guide. The copier starts copying. Do not release the original until it is fed into the copier. Variable Cutting This function cuts roll paper in a length you specify. S The variable cut can handle the cut length from 245 to 3, 600 mm, 9. 6" to 142". 1 Press the Cut Select key to turn on the "Variable Cut" indicator. 2 Press the + and - keys to specify the length for the variable cut. You can specify the cut length quickly by displaying the nearest value with the Paper Size key and changing it to the desired one. COPYING 17 COPYING ONTO ROLL PAPER 3 Set the original guide to match the original width and direction. 4 Insert the original lightly along the original guide. The copier starts copying. Do not release the original until it is fed into the copier. 18 COPYING PARTIAL COPYING The Partial Copy function copies only a part of an original. This function specifies the start and end points in the original feed direction. S The Partial Copy function cannot apply to originals having a length of less than 245 mm, 9. 6" in the paper feed direction. S The Partial Copy function cannot be used when the Sample Copy function is selected. S The start and end points cannot be set within 162 mm, 6. 4" from the leading edge of paper. S The spacing between the start and end points is 100 mm, 4. 0" at the minimum. S Roll paper is cut in 250 mm, 9. 9" at the minimum. 1 Press the Partial Copy key. The indicator on the Partial Copy key blinks. When you press the Partial Copy key again, the leading edge of an original becomes the start point for partial copying. When you press the Partial Copy key for the third time, you can cancel partial copying. 2 Set your original. The copier starts copying. Do not release the original until it is fed into the copier. COPYING 19 PARTIAL COPYING 3 Press the Partial Copy key when the leading edge of the area to be copied comes to the position where it is covered with the original table cover. The indicator on the Partial Copy key lights. If you do not press the Partial Copy key, the original is delivered without partial copying. Original feed direction 4 Press the Partial Copy key when the trailing edge of the area to be copied comes to the position where it is covered with the original table cover. The indicator on the Partial Copy key goes off. If you do not specify the trailing edge, the copier will do the following: · Cuts the paper automatically according to the original length when the synchro cut function is selected. · The area to be copied might differ slightly from the desired one depending on the timing of pressing the key. Original feed direction 20 COPYING SAMPLE COPYING The Sample Copy function copies an original in 245 mm, 9. 6" from its leading edge in the paper feed direction. This allows you to check the copy condition of the current settings in advance. 1 Press the Sample Copy key. The indicator on the Sample Copy key is lit. When you press the Sample Copy key again, you can cancel sample copying. 2 Set your original. Do not release the original until it is fed into the copier. 3 The copier starts copying. COPYING 21 PAPER TYPE/ROLL WIDTH ENTRY FUNCTION This function allows you to store the paper type and roll width for a selected paper feeder. When you change the paper feeder to the specified one, the paper type and roll width are set to the stored values. 1 Press the Paper Select key until your desired paper feeder indicator blinks. The roll paper width is displayed in the paper cut length indicator. You can press the Clear Modes key to cancel the indication. 2 Press the Paper Select key to select the paper feeder. 3 Press the Paper Size key to select the roll paper width. When you select "Manual Feed" for the paper feeder, you cannot specify the paper size. 4 To use the New-ABCDE-size paper, select "New size" using the + and - keys. When the paper feeder indicator blinks for "New size", the 24, 18, 12, and 9 indicators are lit. 22 COPYING PAPER TYPE/ROLL WIDTH ENTRY FUNCTION 5 Press the Fusing Temperature key to select the paper type. 6 Press the Enter key. The above settings are stored. If you do not want to store the settings, press the Clear Modes key. COPYING 23 USING THE PROGRAM FUNCTION The Program function allows you to store a collection of copy settings as programs 1 to 9 and switch them as needed. Programming a Collection of Copy Settings 1 Press the Program key. The indicator on the Program key blinks. The copy counter displays the current program number. 2 Use the and keys to select a program number for which you store copy settings. You cannot change settings in Program No. Each time you make a copy, the copy settings are stored in Program No. 0 is selected. When 3 Press the Enter key. The indicator on the Program key blinks. 24 COPYING USING THE PROGRAM FUNCTION 4 Specify values for each setting. You can store the following settings with the Program function. For the way to specify values, see the corresponding pages. · Sample copying See page 21. [. . . ] Place the film on a flat surface until the remaining heat is removed from the film. Once you unpack the container of paper, store the paper in a polyvinyl bag in the following locations: · Location free from direct sunlight · Location with the humidity of 70 % or less · Flat location Toner S Store toner cartridges levelly in the following locations: · Location free from direct sunlight · Locations the toner could be subjected to temperature of over 35 °C, 95 °F toner or toner containers. might ignite when Toner dust Dispose of the used toner container according to local regulations. Ë Do not eat or swallow toner, and keep it out of reach of children. 54 MAINTAINING YOUR COPIER WHERE TO PUT YOUR COPIER This section shows the precautions you should follow when you move the copier if your office changes the equipment layout or moves to another location. [. . . ]