User manual RICOH MP5308D-E INSTALLATION

[. . . ] Specifications MP5308D: Type: Interface: Data buffer memory: Data transfer speed: CD and DVD Write/Read speed (Ave. ): Internal type Enhanced-IDE (ATAPI) 2MB 33. 3MB/sec. (Max. ) (UDMA33) CD-ROM Speed: 4X: 600KB/sec. , 8X: 1200KB/sec. , 10X: 1500KB/sec. , 16x: 2400KB/sec. , 32X: 4. 8MB/sec. , 40x: 6. 0MB/sec CD-R: 4X: 600KB/sec. , 8x: 1200KB/sec. , 16x: 2400KB/sec. , 24X: 2400-3600KB/sec. , 32X: 2400-4800KB/sec. , CD-RW: 16X: 2400KB/sec. , 10X: 1500KB/sec. , 4x: 600KB/sec. DVD±R: 8X: 5. 5MB/sec. (MAX) DVD±RW: 4X: 5. 5-11MB/sec. (MAX) DVD-ROM Speed: 8X: 10. 8MB/sec. (MAX) 120msec. [. . . ] Master/Slave setting is determined by a jumper on the Jumper Connector. The following table shows the possible jumper settings. CS : (Cable Select) SL : (Slave) MA : (Master) Name MA (Master) SL (Slave) Function Drive set as Master (factory default) Drive set as Slave CS Drive mode set by CSEL (Cable Select) on the host IDE interface Jumper Connector 3. Insert the drive unit into the 5-inch bay horizontally, and secure it using the provided screws. Connect the 4-pin power cable from the computer's power supply to the power connector at the drive's rear panel. If there is no spare cable available in the computer, it will be necessary to purchase a splitter cable. If a sound card is present in the computer, connect the drive to the sound card with the audio cable. If the drive is not recognized on the computer, check to see if the port is enabled in the BIOS. For more detailed explanation, refer to the manual of the computer. L/R connectors Drive Primary or Secondary Sound card 8. Mother board It is not necessary to install any special device drivers. In order to ensure normal drive operation (or if the drive is not recognized by your computer), please check the following. GB Thank you for purchasing the RICOH CD-R/RW or DVD+RW/+R drive (hereafter referred to as the ('drive'). In order to ensure the drive's long lasting operating efficiency, it must be properly installed. Please follow these procedures carefully. In order to ensure normal drive operation · For Windows ME/98/95 Users - The driver is located in [control panels] - [system] - [device manager] - [CD-ROM]. 4. 0 Users - The drive is located on the IDE controller in [control panels] - [SCSI adapter] - [devices]. · For Windows 2000 and XP Users - The drive is located in [control panels] - [System] - [hardware] - [device manager]. If the drive is not recognized by your computer · For Windows ME/98/95 Users - If a [!] indicator is displayed on the IDE controller in [control panels] - [system] -[devices manager]-[harddisk controllers], you will need to contact your PC's manufacturer or the motherboard's manufacturer and get the appropriate IDE controller driver. 4. 0 Users - If a [!] mark is displayed on the IDE controller in [control panels] - [SCSI adapter] -[devices], you will need to contact your PC manufacturer or the motherboard manufacturer and get the appropriate SCSI controller driver. [. . . ] - The manual method mentioned here is used only for emergency purposes. Using the manual method for any other purpose may result in malfunctioning of the drive. Slowly and gently pull out the disc tray. http://www. ricohpmmc. com GB * All references to the product in this document are to specifications in effect when the product was released. Copyright RICOH Co. Ltd. [. . . ]