User manual RICOH MP6200A

[. . . ] Please take notice that the manufacturer will bear no responsibility for direct or indirect damages caused by the use of this product or its malfunction. Please take notice that the manufacturer will bear no responsibility for damage to data caused by this product. Please backup (copy) all important data as protection against data loss. MS-DOS, Windows, and Windows 95 are trademarks registered in the United States and other countries by the Microsoft Corporation. [. . . ] When a illegal disc is loaded or some hardware trouble occurs, the indicator blinks. 5 The MP 6200AR Series 3. 2 Rear panel Analog Audio Output Connector Jumper Connector Power connector The MP 6200AR Series Digital Audio Output Connector Name Power Connector IDE Interface Connector IDE Interface Connector Jumper Connector Analog Audio Output Connector Digital Audio Output Connector Function Connects to the power supply (5- and 12-V DC) of the host computer. Connecting the wrong way may damage the system (and is not guaranteed). Connect to the IDE (Integrated Device Electronics) interface using a 40-pin flat IDE cable. Do not connect or disconnect the cable when the power is on, as this could cause a short circuit and damage the system. This jumper determines whether the drive is configured as a master or slave. Changing the master-slave configuration takes effect after power-on reset. Enhanced IDE (EIDE/ATAPI) Setup Before installation, set the jumper on the jumper connector on the rear panel. The drive can be connected as the Master or Slave on an EIDE (ATAPI) interface. When several (up to four) EIDE devices are connected, each must be set in a unique way. Specific knowledge of hardware and software is necessary to install the drive. We cannot guaranty against direct or indirect damage resulting from improper connections. If two peripheral devices with the same settings are both connected to the Primary or to the Secondary EIDE bus, the host computer may fail to run, or may malfunction, so careful attention is necessary. The MP 6200AR Series CS: Cable Select (CSEL) SL: Slave MA: Master Make sure that the host computer is turned OFF when connecting or removing a jumper. If connected horizontally as shown in Figure 2, the drive may malfunction or be damaged. Figure 1. (Master setting) Figure 2. 7 Only one jumper should be installed on the jumper connector. If more than one jumper is installed, the drive may malfunction or be damaged. Master/Slave setting is determined by jumper installation on the Jumper Connector. The following table shows the possible jumper settings. Name MA (Master) SL (Slave) CS Drive mode set by CSEL Drive set as Slave Function Drive set as Master (factory default) The MP 6200AR Series (Cable Select) on the host IDE interface A hard disk is normally installed as the Primary Master on the EIDE (ATAPI) interface. Other EIDE peripheral devices such as hard drives and CD-ROMs are then set differently. 8 4. 1 PC Connections The MP 6200AR Series The CD-RW drive connects to the motherboard of the host computer using an IDE interface cable. Both Primary and Secondary connectors are usually provided on the motherboard, which may be connected as follows: Master Master Slave Slave Primary Secondary Motherboard 9 To Install as a Master Drive To install the drive as a Master, the jumper can be left as supplied from the factory. The MP 6200AR Series Master drive (Booting hard disk) Master drive (CD-RW drive) Primary connector Secondary connector Master drive (Booting hard disk) Master drive (CD-RW drive) Slave drive (Other IDE drive) Primary connector Secondary connector 10 Master drive (Booting hard disk) Master drive (CD-RW drive) Slave drive (Other IDE drive) Primary connector Secondary connector 11 The MP 6200AR Series To Install as a Slave Drive To install the drive as a Slave, change the jumper setting on the rear panel. The MP 6200AR Series Master drive (Booting hard disk) Slave drive (CD-RW drive) Primary connector Secondary connector Master drive (Booting hard disk) Master drive Master drive (Other IDE drive) 12 Master drive (Booting hard disk) Master drive (Other IDE drive) Primary connector Slave drive (CD-RW drive) Secondary connector 13 The MP 6200AR Series 5. How to Use the Discs When using CD-ROM discs, CD-R discs or CD-RW discs, don't attach any stickers or labels to the discs. Using discs with them attached not only causes read and write errors, but data on the disc may be lost due to damage to the disc itself. The MP 6200AR Series 5. 1 Load the disc ()Press the eject button. 1 (2)Place the disc on the disc tray. When using a 120mm CD, place it in the large round depression. [. . . ] Specifications < Drive > Type Interface Data buffer memory Data transfer speed (SCSI I/F) Write/Read speed (Ave) Internal type (bare drive) Enhanced-IDE (ATAPI) 1MB 5MB/sec. (Mode1, Mode2 Form1) *1 Average access time Initial processing time Mounting direction Compatible formats 1× : 171KB/sec. or less Level Format CD-DA CD-ROM CD-ROM + CD-DA CD-ROM XA <Write> <Read> <Play> Loading system Power Power consumption Weight Dimensions Reliability Error Rate MTBF MTTR Environmental Conditions Temperature Humidity Vibration Auto-loading/Auto-eject DC5V, DC12V 8w (Max. ) Less than 1. 5 Kg. 0 × 203 × 41. 5 mm (Width, depth, height) 10-12 bits or less 100, 000 hours or greater Within 30 minutes When operating 5°C to 40°C ( air cooling) No 5°C to 50°C (With air cooling) 5% to 90% R. H. [. . . ]