User manual RICOH MP7040A

[. . . ] Please take notice that the manufacturer will bear no responsibility for direct or indirect damages caused by the use of this product or its malfunction. Please take notice that the manufacturer will bear no responsibility for damage to data caused by this product. Please backup (copy) all important data as protection against data loss. Adaptec, and the Adaptec logo are trademarks of the Adaptec Corporation. [. . . ] This is because the CD-RW discs allow you to rewrite information that has already been recorded. vi Features: Ricoh's original completely sealed door construction provides high reliability. Running OPC*1 gives a flatter writing signal that improves reliability. Enhanced-IDE (ATAPI) model Can read not only CD-R and CD-RW discs, but also video CDs, music CDs, and photo CDs. Can read data at 20x speed (3MB/sec data transfer rate) and write data at 4x speed (600KB/sec data transfer rate). The recorded CD-RW media can be played in a DVD player or a multiread CD-ROM Player, maintaining future compatibility. Supports random UDF for easy writing to CD-RW discs. *1 Continuously monitors the signal level during recording and adjusts the laser power to compensate when the disc is dirty, insuring a flat signal. vii The MP 7040A Series MP 7040A Series 1 1. System environment This unit can be operated in the system environment explained here. CPU System requirements Memory 100 MHz (or faster) Pentium (for 4x speed, 166MHz or faster recommended) Windows 98/95: 32MB or greator. 4. 0: 32MB or greator (64MB or over recommended) Hard disk with average access time of 19msec or less, and data transfer speed of 1, 200KB/sec or greater. 75MB or more free space. (The free space needed for writing depends on the quantity of data. ) Enhanced-IDE interface (as Primary Slave, Secondary Master, or Slave) 5. 25-inch half height bay required +5V/+12V power socket required Windows 98/95, Windows NT Workstation Ver. 4. 0 (Service Pack 3) or later*1 Ricoh, Kao, Mitsubishi Chamical, Taiyo Yuden, Mitsui Toatsu, TDK or Kodak discs are recommend. MP 7040A Series Harddisk Interface Drive bay Power Sofyware Required OS CD-R, CD-RW discs Occasionally the CD-R and CD-RW discs written by the CD-R/RW drive cannot be read by other CD drives*2. * 2 The disc written using the CD-R/RW drive might not be readable by CDROMs other than Multi-read compatible (Random UDF compatible) CDROMs. Multiread compatible (Random UDF compatible) CD-ROMs are: CD-ROMs that can read low reflectance CD-ROMs that support Packet Write. 2 2. Drive functions and settings 2. 1 Front Panel Disc tray Volume control Headphone jack Name Disc tray Eject button Power/busy indicator Eject button Volume control Headphone jack Power/Busy indicator Function This is the tray for the disc. Place the disc on the ejected disc tray, then lightly push the tray (or push the eject button) and the CD will be loaded. It can't be used to adjust the output volume for the audio output connectors on the rear panel. This indicator is not illuminated unless the disk is currently being accessed. When the disc tray or disc is being accessed, the light shines or flashes orange. Even when a disc is loaded and a disc is not being accessed, the light shines grean. When a illegal disc is loaded or some hardware trouble occurs, the indicator blinks. 3 MP 7040A Series 2. 2 Rear panel Analog Audio Output Connector Jumper Connector Power connector MP 7040A Series Digital Audio Output Connector IDE Interface Connector Name Power Connector IDE Interface Connector Jumper Connector Analog Audio Output Connector Digital Audio Output Connector Function Connects to the power supply (5- and 12-V DC) of the host computer. Connecting the wrong way may damage the system (and is not guaranteed). Connect to the IDE (Integrated Device Electronics) interface using a 40-pin flat IDE cable. Do not connect or disconnect the cable when the power is on, as this could cause a short circuit and damage the system. This jumper determines whether the drive is configured as a master or slave. [. . . ] With your finger, rotate the tabs inwards until you hear a click, so they face the center of the tray. Make sure the eject button is at the top of the unit when installing the unit in a vertical position. MP 7040A Series 20 Appendix 21 Appendix 1. Specifications < Drive : MP7040A> Type Interface Data buffer memory Data transfer speed Write/Read speed (Ave) Internal type (bare drive) Enhanced-IDE (ATAPI) 2MB 16. 7MB/sec. or less horizontal/vertical(eject button at top when vertical) Format CD-DA CD-ROM CD-Extra CD-ROM XA Photo CD CD-I CD-ROM + CD-DA Loading system Power Power consumption Weight Dimensions Reliability Error Rate MTBF MTTR Environmental Conditions Temperature Humidity Video CD Tray type (automatic loading/eject) DC5V, DC12V 12w max (normal operation) 6w max (standby) Less than 1. 5 Kg. [. . . ]