User manual RICOH MP7060A

[. . . ] Please take notice that the manufacturer will bear no responsibility for direct or indirect damages caused by the use of this product or its malfunction. Please take notice that the manufacturer will bear no responsibility for damage to data caused by this product. Please backup (copy) all important data as protection against data loss. Adaptec, and the Adaptec logo are trademarks of the Adaptec Corporation. [. . . ] When loaded with a rewritable CD-RW disc, you can record, read and edit any kind of data. This is because the CD-RW discs allow you to rewrite information that has already been recorded. iv Features: Ricoh's original completely sealed door construction provides high reliability. Running OPC*1 gives a uniform writing signal that improves reliability. Compliant with industry standard Orange Book Part II (CD-R) and Part III (CD-RW). Enhanced-IDE (ATAPI) model Can read not only CD-R and CD-RW discs, but also video CDs, music CDs, photo CDs, and CD-Text Can read data at 24x speed (3. 6MB/sec data transfer rate) and write data at 6x speed*2 (900KB/sec data transfer rate). The recorded CD-RW media can be played in a DVD player or a multiread CD-ROM Player, maintaining future compatibility. Supports random UDF for easy writing to CD-RW discs. *1 Continuously monitors the signal level during recording and adjusts the laser power to compensate when the disc is dirty, insuring a uniform signal. 2 Can write to CD-RW discs at 4X speed (600 KB/second data transfer * rate). v The MP 7060A Series 1 1. System environment This unit can be operated in the system environment explained here. System requirements CPU Memory 166MHz (or faster) Pentium Windows 98/95: 32MB or greater. 4. 0: 32MB or greater (64MB or more recommended) Hard disk with average access time of 19msec or less, and data transfer speed of 1, 200KB/sec or greater. 75MB or more free space. (The free space needed for writing depends on the quantity of data. )*1 Enhanced-IDE interface (as Primary Slave, Secondary Master, or Slave) 5. 25-inch half height bay required +5V/+12V power socket required Windows 98/95, Windows NT Workstation Ver. 4. 0 (Service Pack 3) or later Ricoh, Mitsubishi Chemical, Taiyo Yuden, Mitsui Chemicals, Ritek, CMC, Princo, TDK or Kodak discs are recommended. MP 7060A Series Harddisk Interface Drive bay Power Software Required OS CD-R, CD-RW discs Occasionally the CD-R and CD-RW discs written by the CD-R/RW drive cannot be read by other CD drives*2. * 1 For write at 6X speed, average access time of 12 msec or less and data transfer speed of 5 MB/sec or greater are recommended. * 2 The disc written using the CD-R/RW drive may not be readable by CDROMs other than Multi-read compatible (Random UDF compatible) CDROMs. Multiread compatible (Random UDF compatible) CD-ROMs are: (1) CD-ROMs that can read low reflectance (2) CD-ROMs that support Packet Write. 2 2. Drive functions and settings 2. 1 Front Panel Disc tray Volume control Headphone jack Eject button Drive activity indicator Name Disc tray Eject button Volume control Headphone jack Drive activity indicator Function This is the tray for the disc. Place the disc on the ejected disc tray, then lightly push the tray (or push the eject button) and the CD will be mounted. It can't be used to adjust the output volume for the audio output connectors on the rear panel. If no CD is mounted, the indicator does not light even when the power is turned on. When a illegal disc is loaded or some hardware trouble occurs, the indicator blinks. 3 MP 7060A Series 2. 2 Rear panel Analog Audio Output Connector Jumper Connector Power connector MP 7060A Series Digital Audio Output Connector IDE Interface Connector Name Power Connector IDE Interface Connector Jumper Connector Analog Audio Output Connector Digital Audio Output Connector Function Connects to the power supply (5- and 12-V DC) of the host computer. Connecting the wrong way may damage the system (and is not guaranteed). Connect to the IDE (Integrated Device Electronics) interface using a 40-pin flat IDE cable. [. . . ] With your finger, rotate the tabs inwards until you hear a click, so they face the center of the tray. The disk is inserted on the inside of these tabs. Make sure the eject button is at the top of the unit when installing the unit in a vertical position. MP 7060A Series 20 Appendix 21 1. Specifications < Drive : MP7060A> Type Interface Data buffer memory Data transfer speed Write/Read speed (Ave) Internal type (bare drive) Enhanced-IDE (ATAPI) 2MB 11. 1MB/sec. horizontal/vertical(eject button at top when vertical) Format <Write> <Read> <Play> CD-DA CD-ROM CD-Extra CD-ROM XA Photo CD CD-I CD-ROM + CD-DA Video CD CD-Text Tray type (automatic loading/eject) DC5V, DC12V 12w max (normal operation) 6w max (standby) Less than 1. 5 Kg. [. . . ]