User manual RICOH MP7060S

[. . . ] Please take notice that the manufacturer will bear no responsibility for direct or indirect damages caused by the use of this product or its malfunction. Please take notice that the manufacturer will bear no responsibility for damage to data caused by this product. Please backup (copy) all important data as protection against data loss. Adaptec, and the Adaptec logo are trademarks of the Adaptec Corporation. [. . . ] Supports random UDF for easy writing to CD-RW discs. *1 Continuously monitors the signal level during recording and adjusts the laser power to compensate when the disc is dirty, insuring a uniform signal. 3 Can write to CD-RW discs at 4X speed (600 KB/second data transfer * rate). v The MP 7060S Series 1 1. System environment This unit can be operated in the system environment explained here. System requirements CPU Memory 166MHz (or faster) Pentium Windows 98/95: 32MB or greater. 4. 0: 32MB or greater (64MB or more recommended) Hard disk with average access time of 19msec or less, and data transfer speed of 1, 200KB/sec or greater. 75MB or more free space. (The free space needed for writing depends on the quantity of data. )*1 Adaptec Inc. 5. 25-inch half height bay required +5V/+12V power socket required Windows 98/95, Windows NT Workstation Ver. 4. 0 (Service Pack 3) or later Ricoh, Mitsubishi Chemical, Taiyo Yuden, Mitsui Chemicals, Ritek, CMC, Princo, TDK or Kodak discs are recommended. MP 7060S Series Hard disk SCSI Interface Drive bay Power Software Required OS CD-R, CD-RW discs Occasionally the CD-R and CD-RW discs written by the CD-R/RW drive cannot be read by other CD drives*2. * 1 For write at 6X speed, average access time of 12 msec or less and data transfer speed of 5 MB/sec or greater are recommended. 2 * The disc written using the CD-R/RW drive may not be readable by CDROMs other than Multi-read compatible (Random UDF compatible) CDROMs. Multiread compatible (Random UDF compatible) CD-ROMs are: (1) CD-ROMs that can read low reflectance (2) CD-ROMs that support Packet Write. 2 2. Drive functions and settings 2. 1 Front Panel Disc tray Volume control Headphone jack Eject button Drive activity indicator Name Disc tray Eject button Volume control Headphone jack Drive activity indicator Function This is the tray for the disc. Place the disc on the ejected disc tray, then lightly push the tray (or push the eject button) and the CD will be mounted. It can't be used to adjust the output volume for the audio output connectors on the rear panel. When a disc is mounted into the drive and the disc is being accessed, it flashes or lights orange. When an illegal disc is mounted or hardware trouble occurs, the indicator blinks. 3 MP 7060S Series 2. 2 Rear panel Option connector SCSI interface connector Power connector MP 7060S Series Audio output connector Name Power Connector Function Connects to the power supply (5- and 12-V DC) of the host computer. Connecting the wrong way may damage the system (and is not guaranteed). SCSI interface connector Use a 50 pin double-end flat SCSI cable to connect to the SCSI interface. Connecting or disconnecting connectors while power is on may result in a short circuit, causing damage to the equipment. When connecting or disconnecting connectors, make sure to turn off the power beforehand. Don't use jumpers to change anything besides the SCSI ID, but keep the drive as initially set(no jumper pins: ID 0) SCSI ID changes become valid after power is turned off, then on again. Installing jumper pins besides the ones for SCSI ID settings may be the cause of damage or abnormal drive operation. Installing the Drive 3. 1 Before Installation Before installing the drive, please note the following points. [. . . ] If this is done, the tabs on the disk tray will need to be rotated to stop the disk from falling out. With your finger, rotate the tabs inwards until you hear a click, so they face the center of the tray. The disk is inserted on the inside of these tabs. Make sure the eject button is at the top of the unit when installing the unit in a vertical position. 19 Appendix 21 1. Specifications < Drive : MP7060S> Type Interface Data buffer memory Data transfer speed Write/Read speed (Ave) Internal type (bare drive) SCSI-2 2MB Max. [. . . ]