User manual RICOH MP7080A

[. . . ] Please backup (copy) all important data as protection against data loss. q q q q PC DOS is a trademark of IBM Inc. MS-DOS, Windows, Windows ® 95 and Windows ® 98 are trademarks registered in the United States and other countries by the Microsoft Corporation. The company names and product names written in this manual are trademarks or registered trademarks. Conventions This manual uses the following symbols which indicate important information. Be sure to read the information. Ignoring this warning and incorrect handling may result in serious personal injury or damage to the product. Indicates restriction or caution that you should notice. Provides useful additional information. Introduction This manual contains important notes and product handling information. [. . . ] Multi-read compatible (Random UDF compatible) drives are necessary. Multi-read compatible (Random UDF compatible) drives are: q q Drives that can read low reflectivity discs. Drives that support Packet Write. Specifications Drive | Disc Drive : MP7080A Type Interface Data buffer memory Data transfer speed CD-R/CD-RW Write/Read speed (Ave. ) Internal type Enhanced-IDE (ATAPI) 4MB 16. 7MB/sec. (Mode2, From2) Average access time Initial processing time 120msec. or less horizontal/vertical Format CD-DA CD-ROM CD-Extra CD-ROM XA Photo CD*3 CD-i*3 Video-CD CD-Text Write Read Play*2 Mounting direction Compatible formats * * * * * * * * * * * * * * * * * * Loading system Power Power consumption Weight Dimensions Reliability Tray type (automatic loading/eject) DC5V, DC12V 12w max. 146. 0 X 193. 0 X 41. 3mm Error Rate: MTBF: MTTR: 10-12 bits or less 100, 000hours or greater Within 30 minutes Environmental Conditions Temperature Humidity Vibration When operating 5°C to 40°C (No air cooling) 55% to 90% R. H. (No condensation) 0. 035mmpp(10 to 45Hz) 0. 025mmpp(45 to 65Hz) 0. 2 X 9. 8 m/s2 (65 to 150Hz) When not operating -30°C to 65°C 5% to 95% R. H. (No condensation) 1 X 9. 8 m/s2 (5 to 300Hz) Shock Environmental dust 2 X 9. 8 m/s2 40 X 9. 8 m/s2 (6msec. half sine) Class 3 million or less (3 million particles of 0. 5 micron dustper cubic foot or less) *1 Speed is automatically reduced if reading is unsuccessful. The drive's appearance and specifications may change without notice. Disc CD-R Characteristic External diameter Dimensions Internal diameter Thickness Recording area (User area) Time Recording capacity Track pitch Substrate material Capacity Linear speed 80min. *1 700MB 1. 2m/s CD-R ø120mm ø15mm 1. 2mm ø50 to 116mm 74min. 650MB 1. 2m/s 1. 6 ± 0. 1µm Polycarbonate Organic pigment (phthalocya-nine) / Au or Ag lamination (Organic protective layer attached) 65% or more 70µm or less 0. 4° or less 6 to 7mW(at :785nm, NA:0. 5) 63min. 550MB 1. 4m/s 80min. *2 700MB 1. 2m/s 1. 6 ± 0. 1µm Polycarbonate Ag-In-Sb-Te phase change recording material 15 to 20% 70µm or less 0. 4° or less 8 to 14mW(at :785nm, NA:0. 5) CD-RW CD-RW ø120mm ø15mm 1. 2mm ø50 to 116mm 74min. 650MB 1. 2m/s Recording material Reflectance (R to p) Eccentricity Maximum camber angle Recommended recording power Playback power Playback stability 1mW or less or more (Playback power = 0. 7mW) -5 to 55°C 106times 1mW or less 106times or more (Playback power = 1mW) 10 to 40°C 10 to 80%RH 30 years or more (5 to 25°, 5 to 60%RH) 1, 000 times or more Environment for use 5 to 95%RH Storage life Number of rewrites * * 100 years or more (5 to 25°C, 5 to 60%RH Avoiding direct sunlight) ------------ The above specifications are for Ricoh CD-R and CD-RW discs Recommended Discs CD-R (74min. /63min. ) : Ricoh, Taiyo Yuden, Mitsubishi Chemical, Mitsui Chemicals, Ritek, CMC, Princo, TDK, Kodak, Memorex, Philips, and Maxell discs Taiyo Yuden, TDK, Maxell, Philips CD-R (80min. )*1 : CD-RW : Rioch, Mitsubishi Chemical, Memorex Philips CD-RW (80min. )*2 : For the latest disc information, please refer to Ricoh's website. Drive functions and settings Front Panel | Rear panel Front Panel 1. Disc tray This is the tray for the disc. Always turn the power OFF when connecting or disconnecting the cable. 5. Power Connector Connects to the power supply (5 and 12V DC) of the host computer. Caution Be careful to connect with the proper way. Connecting the wrong way may damage the system (and is not guaranteed). Emergency Eject This drive has a function that allows the CD to be ejected manually, if this becomes necessary in an emergency such as failure of the drive or a power outage. Follow the following procedures in such a case. Caution This feature is a last measure to be used only in an emergency. Pull the front door to open it all the way, then grip the disc tray between thumb and forefinger and gently pull it straight out. Note If you cannot get a good grip on the disc tray with your fingers, use a steel binder clip or spring clamp to pull it out. Disc ejection 1. Press the eject button or push the disc tray and the tray will be inserted back into the drive. Caution After ejecting the disc, return the disc tray inside the unit quickly. When the disc tray is in the ejected position, dust and other debris will enter, possibly causing read errors, write errors, or drive failure. Back Load the disc |Disc ejection | Emergency Eject Using the Drive in a Vertical Position Next Load the disc 1. Place the disc on the disc tray. Caution r r r r When using a 120mm CD, place it in the large round depression. Load the disc by pressing the eject button or by lightly pushing in the disc tray. Next Load the disc | Disc ejection | Emergency Eject Using the Drive in a Vertical Position Using the Drive in a Vertical Position The drive can be installed in a vertical position. When loading a disc, insert it into the inner side of the tabs. Caution r r Make sure the eject button is at the top of the unit when install the unit in a vertical position. Cannot be used with 80mm CDs. Back Load the disc | Disc ejection | Emergency Eject Using the Drive in a Vertical Position Installing the Drive Specific knowledge of hardware and software is necessary to install the drive. [. . . ] Device Drivers 6. Sound Card Connection If the computer has a sound card, the drive can be connected to the sound card with an audio cable. Make sure the connections are oriented so that L corresponds to L and R to R. Refer to the manual for the sound card for detailed information regarding connection. Audio digital output The drive supports S/PDIF(IEC958) for digital audio output. As long as the sound board comes with S/PDIF input, it can be connected externally to the D/A converter. [. . . ]