User manual RICOH MP7083A

[. . . ] The volume that exceeds 70dB occurs and the obstacle sometimes breaks out. Declaration of Conformity "The Product complies with the requirements of the EMC Directive 89/366/EEC and the Low Voltage Directive 73/23/EEC. " q Please take notice that the manufacturer of this equipment does not offer any warranty against data loss due to inappropriate installation or handling, or direct or indirect damages. Please take notice that the manufacturer will bear no responsibility for direct or indirect damages caused by the use of this product or its malfunction. Please take notice that the manufacturer will bear no responsibility for damage to data caused by this product. Please backup (copy) all important data as protection against data loss. q q q q q q PC DOS is a trademark of IBM Inc. [. . . ] *2 The speed at which to write on the current standard CD-RW discs is 4x recording (at a data transfer rate of 600KB/sec). Explains the system environment required for using the drive as a CD-R/CD-RW drive. PC Operating System IBM PC/AT compatible Windows 98/95(OSR2 or later) Windows NT Workstation Ver. 4. 0 (Service Pack 5) or later*1 Windows 2000 (Professional)*1 Pentium 200 MHz or higher Windows NT (Workstation) / 2000 64MB or more (Windows 95/98 32MB or more) Hard disk with average access time of 19msec or less, and data transfer speed of 2, 500KB/sec or greater. Enhanced-IDE interface (as Primary Slave, Secondary Master, or Slave) 5. 25-inch half height bay required +5V/+12V power socket required CD-R(74min): Ricoh, Mitsubishi Chemical, Taiyo Yuden, Mitsui Chemicals, TDK and Maxell discs CD-R(80min): Ricoh, Taiyo Yuden, TDK discs CD-RW: Ricoh and Mitsubishi Chemical discs*2 High Speed CD-RW: Ricoh discs *2 CPU Memory Harddisk Interface Drive bay Power Recommendation discs*3 *1 *2 *3 abCD does not support these Operating System. The disc written using the CD-R/RW drive may not be readable by CD-ROM drives. Even if it is the recommendation disc, some of discs may have possibility to fail writting with highest writting speed with the problem on the disc. In this case, please try to write with lower writting speed, or please try to use another disc. Multi-read compatible (Random UDF compatible) drives are: q q Drives that can read low reflectivity discs. Drives that support Packet Write. Front Panel Rear panel Front Panel 1. Disc tray This is the tray for the disc. Place the disc on the ejected disc tray, then lightly push the tray (or push the eject button) and the disc will be mounted. This might cause damage to the loading section of the drive. 2. Headphone jack This jack is for connecting headphones or mini-speakers. 3. Volume control This is used to adjust the output volume of the headphone jack. It can't be used to adjust the output volume for the audio output connectors on the rear panel. Sudden loud noises can damage your hearing. 4. Busy indicator This indicator lights green when a disc is mounted into the drive. If a disc is not mounted, the indicator does not light even when the power is turned on. When a illegal disc is loaded or some hardware trouble occurs, the indicator blinks. 5. Eject button This is the button used to eject or insert in the disc tray. 6. Emergency eject hole This drive has a function that allows the disc to be ejected manually if this becomes necessary in an emergency such as failure of the drive or a power outage. Caution This feature is a last measure to be used only in an emergency. Using it excessively will cause malfunction. Rear panel 1. Analog Audio Output Connector Provides output to a sound card (Analog signal). 2. Jumper Connector This jumper determines whether the drive is configured as a master or slave. Changing the master-slave configuration takes effect after power-on reset. 3. IDE Interface Connector Connect to the IDE (Integrated Device Electronics) interface using a 40-pin flat IDE cable. Caution Do not connect or disconnect the cable when the power is on, as this could cause a short circuit and damage the system. Always turn the power OFF when connecting or disconnecting the cable. 4. Power Connector Connects to the power supply (5 and 12V DC) of the host computer. Connecting the wrong way may damage the system (and is not guaranteed). Emergency Eject This drive has a function that allows the CD to be ejected manually, if this becomes necessary in an emergency such as failure of the drive or a power outage. Caution This feature is a last measure to be used only in an emergency. Pull the front door to open it all the way, then grip the disc tray between thumb and forefinger and gently pull it straight out. [. . . ] Device Drivers Caution When using CD-ROM discs, CD-R discs or CD-RW discs, do not attach any stickers or labels to the discs. Using discs with labels attached not only causes read and write errors, but data on the disc may be lost due to damage to the disc itself. q q q q Load the disc Disc ejection Emergency Eject Using the Drive in a Vertical Position Drive : MP7083A Type Interface Data buffer memory Data transfer speed CD-R/CD-RW/High Speed CD-RW Write/Read speed (Ave. ) Internal type Enhanced-IDE (ATAPI) 2MB 16. 7MB/sec. (Max. ) (PIO4, DMA2) 32X: 32X: 20X: 20X: 20X: 8X: 8X: 6X: 6X: 6X: 4X: 4X: 4X: 2X: 2X: 2X: 120msec. or less horizontal/vertical (eject button upper) Track At Once, Disc At Once, Multi-session, Packet Write, Session At Once. [. . . ]