User manual RICOH MP7163A

[. . . ] Dieser Druckerüberschreitet einen Geräuschpegel von 70 dB (A) während dem Betrieb nicht. Declaration of Conformity "The Product complies with the requirements of the EMC Directive 89/366/EEC and the Low Voltage Directive 73/23/EEC. " q q Please take notice that the manufacturer of this equipment does not offer any warranty against data loss due to inappropriate installation or handling, or direct or indirect damages. Please take notice that the manufacturer will bear no responsibility for direct or indirect damages caused by the use of this product or its malfunction. Please take notice that the manufacturer will bear no responsibility for damage to data caused by this product. Please backup (copy) all important data as protection against data loss. q q PC DOS is a trademark of IBM Inc. [. . . ] Enhanced-IDE interface (as Primary Slave, Secondary Master, or Slave) 5. 25-inch half height bay required +5V/+12V power socket required CD-R: CD-RW: High Speed CD-RW: *1 *2 *3 Ricoh, Mitsubishi Chemical, Taiyo Yuden, Mitsui Chemicals, TDK and Maxell discs Ricoh and Mitsubishi Chemical discs*2 Ricoh and Mitsubishi Chemical discs CPU Memory Harddisk Interface Drive bay Power Recommended discs*3 At present InCD does not support these Operating Systems. The disc written using the CD-R/RW drive may not be readable by CD-ROM drives. Some discs may fail at the highest writing speed due to a disc problem. In this case, please try to write at lower writing speeds, or please use another disc. Multi-read compatible (Random UDF compatible) drives are: q q Drives that can read low reflectivity discs. Drives that support Packet Writing. Front Panel Rear panel Front Panel 1. Place the disc on the ejected disc tray, then lightly push the tray (or push the eject button) and the disc will be mounted. Headphone jack This jack is for connecting headphones or mini-speakers. 3. Volume control This is used to adjust the output volume of the headphone jack. It can't be used to adjust the output volume for the audio output connectors on the rear panel. Busy indicator This indicator lights orange when a disc is mounted into the drive. If a disc is not mounted, the indicator does not light even when the power is turned on. When a illegal disc is loaded or some hardware trouble occurs, the indicator blinks. 5. Eject button This is the button used to eject or insert in the disc tray. 6. Emergency eject hole This drive has a function that allows the disc to be ejected manually if this becomes necessary in an emergency such as failure of the drive or a power outage. Caution This feature is a last measure to be used only in an emergency. Digital Audio Output Connector Provides output to a sound card (Digital signal). 2. Analog Audio Output Connector Provides output to a sound card (Analog signal). 3. Jumper Connector This jumper determines whether the drive is configured as a master or slave. Changing the master-slave configuration takes effect after power-on reset. 4. A hard disk is normally installed as the Primary Master on the E-IDE (ATAPI) interface. Other E-IDE peripheral devices such as hard drives and CD-ROMs are then set accordingly. Caution q If two peripheral devices with the same settings are both connected to the Primary or to the Secondary E-IDE bus, the host computer may fail to run, or may malfunction, so careful attention is necessary. [. . . ] Repeating this action three times or so ejects the tray out. If you cannot successfully eject the tray by pushing a thin, rigid object in, the situation may be as follows. The four vanes may be oriented just at the angles as shown below. In such a case, push the tip of the thin wire in the following direction with the wire angled at about 15 degrees so that the tray can easily be ejected. Back Next Load the disc Emergency Eject Disc ejection Using the Drive in a Vertical Position Using the Drive in a Vertical Position The drive can be installed in a vertical position. 1. Cannot be used with business card CDs. Back Load the disc Emergency Eject Disc ejection Using the Drive in a Vertical Position Drive : MP7163A Type Interface Data buffer memory Data transfer speed CD-R/CD-RW/High Speed CD-RW Write/Read speed (Ave. ) Internal type Enhanced-IDE (ATAPI) 2MB 33. 3MB/sec. (Max. ) (MultiWord DMA mode 2) <Read Speed> 4x: 600KB/sec 8x: 1200KB/sec 20x: 3000KB/sec*1 32x: 4. 8MB/sec*1 <Write Speed> CD-R 4x: 600KB/sec 8x: 1200KB/sec 12x: 1800KB/sec 16x: 2. 4MB/sec CD-RW 2x: 300KB/sec 4x: 600KB/sec 10x: 1. 5MB/sec Average access time Initial processing time 120msec. [. . . ]