User manual RICOH MP7240A

[. . . ] Dieser Druckerüberschreitet einen Geräuschpegel von 70 dB (A) während dem Betrieb nicht. Declaration of Conformity "The Product complies with the requirements of the EMC Directive 89/366/EEC and the Low Voltage Directive 73/23/EEC. " q q q q Please take notice that the manufacturer of this equipment does not offer any warranty against data loss due to inappropriate installation or handling, or direct or indirect damages. Please take notice that the manufacturer will bear no responsibility for direct or indirect damages caused by the use of this product or its malfunction. Please take notice that the manufacturer will bear no responsibility for damage to data caused by this product. Please backup (copy) all important data as protection against data loss. q q PC DOS is a trademark of IBM Inc. [. . . ] Enhanced-IDE interface (as Primary Slave, Secondary Master, or Slave) 5. 25-inch half height bay required +5V/+12V power socket required CD-R: CD-RW: High Speed CD-RW: Ricoh, Mitsubishi Chemical, Taiyo Yuden, Mitsui Chemicals, TDK and Maxell discs Ricoh and Mitsubishi Chemical discs Ricoh and Mitsubishi Chemical discs CPU Memory Harddisk Interface Drive bay Power Recommended discs Multi-read compatible (Random UDF compatible) drives are: q q Drives that can read low reflectivity discs. Drives that support Packet Writing. Front Panel Rear panel Front Panel 1. Disc tray This is the tray for the disc. Place the disc on the ejected disc tray, then lightly push the tray (or push the eject button) and the disc will be mounted. This might cause damage to the loading section of the drive. 2. Headphone jack This jack is for connecting headphones or mini-speakers. 3. Volume control This is used to adjust the output volume of the headphone jack. It can't be used to adjust the output volume for the audio output connectors on the rear panel. Sudden loud noises can damage your hearing. 4. Busy indicator This indicator lights orange when a disc is mounted into the drive. If a disc is not mounted, the indicator does not light even when the power is turned on. When a illegal disc is loaded or some hardware trouble occurs, the indicator blinks. 5. Eject button This is the button used to eject or insert in the disc tray. 6. Emergency eject hole This drive has a function that allows the disc to be ejected manually if this becomes necessary in an emergency such as failure of the drive or a power outage. Caution This feature is a last measure to be used only in an emergency. Using it excessively will cause malfunction. Rear panel 1. Digital Audio Output Connector Provides output to a sound card (Digital signal). 2. Analog Audio Output Connector Provides output to a sound card (Analog signal). 3. Jumper Connector This jumper determines whether the drive is configured as a master or slave. Changing the master-slave configuration takes effect after power-on reset. 4. IDE Interface Connector Connect to the IDE (Integrated Device Electronics) interface using a 40-pin flat IDE cable. Caution Do not connect or disconnect the cable while the power is on, as this could cause a short circuit and damage the system. Always turn the power OFF when connecting or disconnecting the cable. 5. Power Connector Connects to the power supply (5 and 12V DC) of the host computer. Connecting the wrong way may damage the system (and is not covered under the warranty). Emergency Eject This drive has a function that allows the CD to be ejected manually, if this becomes necessary in an emergency such as failure of the drive or a power outage. When using an 80mm CD, place it in the small round depression with its label side facing up. Only reading is possible. ) The face with the label on it should be up. Load the disc by pressing the eject button or by lightly pushing in the disc tray. Next Load the disc Emergency Eject Disc ejection Using the Drive in a Vertical Position Using the Drive in a Vertical Position The drive CANNOT be installed in a vertical position. Cannot be used with business card CDs. Back Load the disc Emergency Eject Disc ejection Using the Drive in a Vertical Position Specific knowledge of hardware and software is necessary to install the drive. We cannot guarantee against direct or indirect damage resulting from improper connections. Ask your supplier for details of the installation procedure. Before Installation Before installing the drive, please note the following points. q q q q You will need the following: r A Phillips head screw driver of a suitable size to fit the securing screws for the drive unit. r The manual for the computer, to know the location of the IDE connector. [. . . ] (Max. ) (Ultra DMA mode 2) <Read Speed> *1 4x, 8x, 12x (CLV) 20x, 32x, 40x (CAV) <Write Speed> CD-R 4x, 8x, 12x (CLV) 16x, 20x, 24x (ZCLV) CD-RW 2x, 4x (CLV) HighSpeed CD-RW 4x, 10 (CLV) Average access time Initial processing time 120msec. or less horizontal & vertical (Eject button must be downside) Track At Once, Disc At Once, Multi-session, Packet Write, Session At Once. Format Write Read Play*2 Mounting direction Writing Mode Compatible formats CD-DA * * * * * CD-ROM CD-Extra * * * * * * CD-ROM XA Photo CD*3 *4 CD-i*3 *4 * * * * * * Video-CD CD-Text Loading system Power Weight Dimensions Reliability Error Rate: MTBF: MTTR: Tray type DC5V, DC12V Less than 1. 0 Kg. 146 X 200 X 41. 3mm 10-12 bits or less 85, 000 hours or greater Within 30 minutes Environmental Conditions Temperature When operating 5°C to 40°C (No air cooling) 5% to 90% R. H. [. . . ]